Following are the notes for a line of stadia levels. The elevation of BM-A is 184.29m. The stadia interval factor is 100.00 and C = 0.381m. Rod readings are taken at height of instrument. Determine the elevations of remaining points and tabulate values accordingly.(3 decimal places) No long explanation needed. STA BM-A TP-1 TP-2 TP-3 BM-B s (m) 1.40 0.97 1.11 0.79 BACKSIGHT a -3°30' -2°33' 0°45' 2°00' VD s (m) 1.07 0.93 1.46 1.04 FORESIGHT a 2°18' -3°56' -0°26' 8°15' VD DE (m) ELEV (m)

Following are the notes for a line of stadia levels. The elevation of BM-A is 184.29m. The stadia interval factor is 100.00 and C = 0.381m. Rod readings are taken at height of instrument. Determine the elevations of remaining points and tabulate values accordingly.(3 decimal places) No long explanation needed. STA BM-A TP-1 TP-2 TP-3 BM-B s (m) 1.40 0.97 1.11 0.79 BACKSIGHT a -3°30' -2°33' 0°45' 2°00' VD s (m) 1.07 0.93 1.46 1.04 FORESIGHT a 2°18' -3°56' -0°26' 8°15' VD DE (m) ELEV (m)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An engineer's level with stadia constant of 0.30 m was set up on the line between A and B, the following crosshair readings were observed. If the stadia interval factor of the levels is 100, determine the length of line AB. Show all your complete solution and illustration (if applicable)
It is required to lay out a line on the ground 500 m. long. The 50 m tape used was 0.015 mlonger at 18 kg. pull and at 30.618o C temperature. If the actual fieldwork will be done attemperature of 22o C and pull of 14 kg was applied being supported at both ends of tape,compute the correct distance to be laid out if the cross-sectional area of tape is 0.02 sq. cm.and weighs 0.686 kg.
a = 3.7 m b = 31 kN-m c = 35 kN
Compute the angle COD from the following set of lines whose magnetic bearings are given: OC, N 34°14’ E and OD, N 53° 22’ W
Note: P = 42.75 kN
Situation5. A line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 20°C under a 50 N pull supported at both ends. During measurement, the temperature is 5 °C and the tape is suspended under a 75 N pull. The line is measured on 3 % grade. Cross-sectional area of the tape is 3 mm^2. a. Compute the actual length of tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance?
USE AREA MOMENT METHOD PLSSS
It is required to layout on the ground a rectangular lot 505.023 m. long and250.012 m. wide. The tape to be used is exactly 100 m at 10 kg. pull and at 28° Ctemperature. If the actual fieldwork will be done at temperature of 32° C, what pull shouldbe used to eliminate the error in tension and what distances should be laid out?
Determine the distance from the point (5, 3) to the line 4x - 2y = 10.
The difference in elevation between line AB is 6.5 m. A 100 meter steel tape was used with a standard pull of 12 kg under a temperature of 300C. The line was measured on a sloping ground and found to be 486.396 m. But during the measurement, the temperature was 180C and the tape wassuspended under a pull of 18 kg. The tape weighs 0.75 kg and it was supported at 0-30-75-100 marks when measuring. Determine the correct slope distance and horizontal distance. A = 0.04 sq. cm. COMPLETE ANSWER PLEASE
1. Two identical channel Sections placed back to back with a clear distance of 50 mm. Given: Channel section C9x13.4 Wide Flange Section W10x33 Angle section L6x4x 3/4 a. Area b. Centroid c. moment of inertia (lx and ly) d. section modulus ( Sx and Sy) e. radius of gyration ( rx and ry)
Give right solution. Help me urgent Where P=58 kN