The following figure shows a belt brake system operating on a brake drum of the hoisting mechanism. It consists of a cylinder with a diameter of 325 mm, the end of which is the elastic belt connected to both ends of the elastic belt by a crank arm articulated at B and the angle of rotation = 225 degrees. And the coefficient of friction is 0.3 and the latching force is f. Find the necessary F to generate a torque of 350 on the cylinder while it is rotating in the direction shown? Note that s = c = 135mm a = 500mm. 35mm following figure shows a belt braking system operating on a brake drum for a lifting mechanism. Itconsists of a drum with a diameter of 325 mm, and the two ends of the flexible belt are connectedwith a crank arm hinged at B and the angle of rotation = 225 °. Shown. Find the magnituderequired to generate a torque of ..350 on the drum while it is rotating in the direction shown?Note that s = 35mm,a = 500mm, cDrumBand of width, wTERRAZAS135,BSRotationSoommQuestion 6: The1Si

Answered: Image /qna-images/answer/297b13a2-904f-4ed9-817f-0d18d1ec4e8f.jpg

following figure shows a belt braking system operating on a brake drum for a lifting mechanism. It consists of a drum with a diameter of 325 mm, and the two ends of the flexible belt are connected with a crank arm hinged at B and the angle of rotation = 225 °. Shown. Find the magnitude required to generate a torque of ..350 on the drum while it is rotating in the direction shown? Note that s = 35mm, a = 500mm, c Drum = 135, Band of width, w 135 Rotation mm T Question 6: The d. Pr

following figure shows a belt braking system operating on a brake drum for a lifting mechanism. It consists of a drum with a diameter of 325 mm, and the two ends of the flexible belt are connected with a crank arm hinged at B and the angle of rotation = 225 °. Shown. Find the magnitude required to generate a torque of ..350 on the drum while it is rotating in the direction shown? Note that s = 35mm, a = 500mm, c Drum = 135, Band of width, w 135 Rotation mm T Question 6: The d. Pr

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.70P: Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at...

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A pulley 610 mm diameter is driven at 300 revs/min by a belt, the tensions in the tight and slack sides of the belt being 670 N and 270 N. Find the power transmitted.
The picture shows the rear swivel axle bearing design of a 4-wheel wagon. It is known that the speed of the wagon wheels is n = 37 rpm. The total radial load carried by the wagon is given as Fr= 16060 Newtons. In addition, due to road conditions, Fa axial load is applied to the wagon. If the axial load on the A bearing is 10% of the radial (vertical) load on this bearing, calculate the dynamic load number (C) of the bearing in the A bearing in Newtons for 18616 hours of life. fo*Fa/Co = 0.345 Pi=3.14
For the slider-crank mechanism shown in the following figure, link 1 rotates counterclockwise. AB=10mm, BC=30mm, e=10mm. Calculate the maximal pressure angle αmax.
A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor spins at a speed of 1150 rpm. The motorcycle runs at a linear speed of 45 km/h on 12-inch wheels. Preliminary center to center distance is 13”. This type of motorcycle requires two strands (conical double sleeve assembly) and is subjected to hard shocks. a) Calculate the effective power.b) Choice of chain and sprocket. (Standard part number, see catalog)c) Calculate the speed ratio. https://pdf.directindustry.com/pdf/martin-sprocket-gear/general-catalog/9091-246439.html
a) An engine has a flywheel mass of 8-tonnes and a turning radius of 3 m. The energy fluctuation is 70 KN-m. The average speed of the engine is 160 rpm. Find the maximum speed value. b) A jet engine has a rotor with a weight of 500 N and this rotor rotates at 2400 rpm. Rotor It is suspended in the middle of the C and D bearings with a total distance of 600 mm between them and the center of gravity is rotated. 35 mm above its centre. By calculating the dynamic forces on the bearings, this system perform the balancing.
Machine design A 60-hp four-cylinder internal combustion engine is used to drive a medium-shock brickmaking machine under a schedule of two shifts per day. The drive consists of two 26-in sheaves spaced about 12 ft apart, with a sheave speed of 400 rev/min. Select a Gates Rubber V-belt arrangement. Find the factor of safety, and estimate the life in passes and hours?
A 3-strand chain and sprocket turns 650 rpm and has a service factor of 1.5. If 15 HP/strand chain is to be used, find the torque that the chain and sprocket can deliver. (Ans. 242.4 ft-lbs)
A 2 in diameter shaft uses a straight spline with seven splines and contact length of 1.5 in. Assuming it is designed to slide while under load, compute it torques transmission capacity at 100 rpm if h is 8% of that shaft diameter. Note S = 1200 psi.
The figure 1 shows a pulley assembly that consists of a shaft supported by two bearings and driven by a motor on the righthand side (not shown in the figure). The shaft diameter is 100mm. The pulley consists of two disks, each disk is 15 mm thick and has an outer diameter of 620mm, that are connected by means of a cylindrical shell. The length of the shell is 500mm, the outer diameter of the shell is 600mm, and the thickness of the shell is 15mm. The pulley drives a belt that places a uniformly distributed load on the shell (of 100000N) as shown in the diagram. The belt lifts a load that applies a torque of 6000Nm to the pulley. The shell and the plates are connected. A 6mm fillet should be applied to all the 90 degree corners between the shaft and the plates and between the shell and the plates. The deflection of the shaft
The figure 1 shows a pulley assembly that consists of a shaft supported by two bearings and driven by a motor on the righthand side (not shown in the figure). The shaft diameter is 100mm. The pulley consists of two disks, each disk is 15 mm thick and has an outer diameter of 620mm, that are connected by means of a cylindrical shell. The length of the shell is 500mm, the outer diameter of the shell is 600mm, and the thickness of the shell is 15mm. The pulley drives a belt that places a uniformly distributed load on the shell (of 100000N) as shown in the diagram. The belt lifts a load that applies a torque of 6000Nm to the pulley. The shell and the plates are connected. A 6mm fillet should be applied to all the 90 degree corners between the shaft and the plates and between the shell and the plates. The highest stress in the system
The figure 1 shows a pulley assembly that consists of a shaft supported by two bearings and driven by a motor on the righthand side (not shown in the figure). The shaft diameter is 100mm. The pulley consists of two disks, each disk is 15 mm thick and has an outer diameter of 620mm, that are connected by means of a cylindrical shell. The length of the shell is 500mm, the outer diameter of the shell is 600mm, and the thickness of the shell is 15mm. The pulley drives a belt that places a uniformly distributed load on the shell (of 100000N) as shown in the diagram. The belt lifts a load that applies a torque of 6000Nm to the pulley. The shell and the plates are connected. A 6mm fillet should be applied to all the 90 degree corners between the shaft and the plates and between the shell and the plates. Apply the boundary conditions and the forces and torques to the system and determine the following: Calculate the highest Principal stresses in the system ?