For a certain pulley system a load of 80 1) kilograms can be lifted 3.0 centimeters by an input force of 100 newtons pulling through a distance of 24.0 centimeters. What are the AMA, IMA, and efficiency for the system? How many strands of the cable (nranda) support the load? 24 cm AMA 100 N IMA - Efficiency pulley system

For a certain pulley system a load of 80 1) kilograms can be lifted 3.0 centimeters by an input force of 100 newtons pulling through a distance of 24.0 centimeters. What are the AMA, IMA, and efficiency for the system? How many strands of the cable (nranda) support the load? 24 cm AMA 100 N IMA - Efficiency pulley system

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The diameters of a small piston and a large piston of hydraulic jack are 2 cm and 10 cm respectively. A force of 60 N is applied in the small piston. Find the load lifted in N by the large piston when the small piston is 20 cm above the large piston. Take the density of the liquid in the jack is 1000 kg/m^3. Include the diagram in your solution. a.1500 b.1520.5 c.1600 d.1625
A submarine is traveling at a depth of ‘95’ kilometers in the ocean, where the gagepressure is 840 Kg(f)/cm2 . The density and bulk modulus of elasticity of water at the top surface of the ocean are 1025 kg/m3 and 24000 kg(f)/cm2 respectively. Find the following:(i) What will be the density of water at the depth of 2.0 kilometers?(ii) What will be specific volume and change of volume at that depth?(iii) What is the pressure at the top surface of the submarine? How much will bechanged in pressure if submarine change direction from North to East?
Nitrogen gas is confined in a cylinder and the pressure of the gas is maintained by a weight placed on the piston. The mass of the piston and the weight together is 100 kg. The acceleration due to gravity is 9.81 m/s2 and the atmospheric pressure is 1.01325 bar. Assume frictionless piston. Determine: (a) The force exerted by the atmosphere, the piston, and the weight on the gas if the piston is 200 mm in diameter. (b) The pressure of the gas. (c) If the gas is allowed to expand pushing up the piston and the weight by 500 mm, what is the work done by the gas in kJ? (d) What is the change in the potential energy of the piston and the weight after the expansion in part (c)?
Include the free body diagram The diameters of a small piston and a large piston of hydraulic jack are 2 cm and 10 cm respectively. A force of 60 N is applied in the small piston. Find the load lifted in N by the large piston when the piston are on the same level.Take density of the liquid in the jack is 1000 kg/m^3. a. 1625 b. 1520.5 c. 1500 d. 1600
The hydraulic jack in the figure is used to lift a 1000 kg mass load to a height y2 = 150 mm. The diameter of the lift cylinder is D = 50 mm. With this information, analyze the system and determine. a) The pressure, in bar.b) The diameter d of the hand pump cylinder, so that the driving force F1 is 50 N. c) If the maximum displacement of the pump pistonfor y1 = 20 mm, how many drives will it take to fully lift the load? d) If you want to reduce the number of actuations by 2/3, keeping the diameter of the lift cylinder, D, the same actuation force F1, and the stroke y1, what geometric changes can be made in the system?
Given the lifting table shown below, The diameter of the plunger DP 20 cm. The ram diameter DR 60 cm , The efficiency is 100 %, The stroke of the plunger is 30 cm. The ram has to raise a load F2 = 20 kN. Find: a) The force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm . c) the volume of oil pumped if the load moves by 30 cm (using plunger force given in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 20cm. (please check the picture carefully).
A force of P = 850 N is applied to the smaller cylinder of a hydraulic jack (Fig.2). The area a of the small piston is 15 cm2 and the area A of the larger piston is 150 cm2. What load W can be lifted on the larger piston if the pistons are at the same level, The mass density ρ of the liquid in the jack is 103 kg /m3.
Given the lifting table shown below , The diameter of the plunger DP 8 cm.The ram diameter DR 48 cm , The efficiency is 100 %, The stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2 kN. Find : a) the force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm c) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8cm .
a) The velocity ratio (VR) b) The mechanical advantage c) The efficiency, Answer in % d) The ideal effort (P1). Answer in N
An industrial fan delivers 55,000 CFM of air through a discharge duct with a size of 3 ft x 4 ft where the static pressure is 6-inch water gage. At the inlet, the duct diameter is 4 ft and the static pressure is 1-inch water gage. The temperature of the air is 78 F and barometric pressure is 14 psia. (ρw = 62.2 lb/ft³). Determine: a). the total pressure in feet of air b). the static power in HP c). the fan power in HP
A hydraulic press has a ram of 30 cm diameter and a plunger of 2cm diameter. it is used for lifting a weight of 30 kN. How much force is required at the plunger? a) 155.5kN b)466.6kN c) 311.1 kN d) 233.3 kN
ρ=1.225 kg/m3 , μ=1.783∗10−5 kg/( m*s) , c=340.3 m/s