For a given power transfer which of the following is true. O Delta is associated with larger line voltage O Delta is associated with larger line current O Star is associated with larger line current O Conductors in delta system have smaller cross sectional area A Transformer having 1400 Primary turns connected to a 252 V a.c. supply. For a secondary Voltage of 416 V, the number of Secondary Turns should be No. of Turns in the Secondary

For a given power transfer which of the following is true. O Delta is associated with larger line voltage O Delta is associated with larger line current O Star is associated with larger line current O Conductors in delta system have smaller cross sectional area A Transformer having 1400 Primary turns connected to a 252 V a.c. supply. For a secondary Voltage of 416 V, the number of Secondary Turns should be No. of Turns in the Secondary

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a) You have been employed as an electrical engineer by a power transmission company to design a short transmission line to supply power to a light-industrial load consumer with power system specification as follows, a 3-ph, 60Hz overhead short transmission line with a line-to-line voltage of 23KV at the load end, line impedance of 2.48 ±j6.57Ω/phase, the industry has a cumulative consumption of 9MW with a power factor of 0.85 of lagging as a result of several induction motor on its production lines.As part of the regulations for connections to the grid, you are to provide justifications and values to the Energy Commission of Ghana.(i) What would be value of the voltage between the live conductor and the neutral, between live and live voltages at the industrial premises of the factory?(ii) What load angle would expect the factory to be operating at?
a plant is feeding a load 1.2k feet away. the load demands 100 amps at 500V. an ac system with transformer rated 500/5000V near the generating station and 5000/500V near the load. if the line has resistance of 0.2 ohms and receiving voltage of 500V, find the sending end voltage and powerflows and transmission losses.
A transformer has a ratio of 4:1. The high voltage side is connected to a 240 Vrms source. The low voltage side (secondary) is connected to an impedance ZL = 20 + j10 Ω.a. What is the value of the load impedance when referred to the primary?b. (in A rms) What is the current out of the source?
A network is composed of the utility having Ssc=250MVA, and an 2000KVA transformer, rated at 20KV/400V (no load), whose voltage impedance is 7%, and whose load losses are 15750watts. the short circuit at the secondary of the transformer using the impedance method is: a)27.01KA b)None of these c)25.8KA d)30KA
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the per-unit impedance of the load. Select one: a. 1736 (45 degree) Ohm b. 36 (90 degree) Ohm c. 1.736 (30 degree) Ohm d. None of the above
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the per-unit current in the line Select one: a. 1.43 A b. 0.569 A c. None of the above d. 2.01
A three-phase system includes a 346.4 V line-to-line supplying a three-phase motor rated 15KVA 0.8pf lag plus additional balanced constant impedance loads. The single-phase representation of the system is shown below. Assume that sources and loads are Y-connected. 1. What is the RMS value of the line current, I in A? 2. If this set of loads will be supplied through a service transformer. What should the minimum size of the transformer in kVA? 3. What should be the size of three-phase capacitor(that will be added to the load mix) to improve power factor to almost 0.95 lag?
A Step-Down Transformer. A transformer connected to a 120 V (rms) ac line is to supply 12.0 V (rms) to a portable electronic device. The load resistance in the secondary is 5.00 Ω. (a) What should the ratio of primary to secondary turns of the transformer be? (b) What rms current must the secondary supply? (c) What average power is delivered to the load? (d) What resistance connected directly across the 120 V line would draw the same power as the transformer? Show that this is equal to 5.00 Ω times the square of the ratio of primary to secondary turns.
A single-phase power system is shown in Fig. 1. The power source feeds a 100-kVA 14/2.4 kV transformer through a feeder1 impedance of 40.0+j150 Ω. The transformer's equivalent series impedance referred to its low-voltage side is 0:12 + j0:5 Ω. The load on the transformer is 90 kW at 0.85 power factor lagging and 2,300 V. a) What is the voltage at the power source of the system ?b) What is the voltage regulation of the transformer ?c) How efficient is the overall power system ?
A Δ-connected, 60−Hz, balanced, 3ϕ, positive-sequence voltage source is connected to a Δ-connected, symmetric 3ϕ load via a non-ideal transmission line. The line-line voltage magnitude of the source is 480VRMS. The series impedance of each phase of the transmission line is 0.1+j1.5Ω. The impedance of each leg of the load is 3+j6Ω. a. What is the total, 3ϕ complex power consumed by the load. b. What are the total active power losses (all three phases) in the transmission line?
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
A 5,000-kVA, 3-phase transformer, 13.2/33-kV, A/Y, has a copper loss of 11 kW. The impedance drop at full-load is 7.5%. Calculate the primary voltage when a load of 4000 kW at 0.8 p.f. is delivered at 33 kv.