A single-phase power system consists of a 400-V 60-Hz generator that is connected to the load Zload = 10 + j20  through the transmission line with Zline = 0.2 + j0.8 . a) What is the voltage at the load? What are the transmission line losses? b) If a 1:N step up transformer and a N:1 step down transformer are placed at the generator and the load ends of the transmission line respectively, what are the new load voltage and the new transmission line losses? Where is N is your Registration Number, MY registraion number is 35

A single-phase power system consists of a 400-V 60-Hz generator that is connected to the load Zload = 10 + j20  through the transmission line with Zline = 0.2 + j0.8 . a) What is the voltage at the load? What are the transmission line losses? b) If a 1:N step up transformer and a N:1 step down transformer are placed at the generator and the load ends of the transmission line respectively, what are the new load voltage and the new transmission line losses? Where is N is your Registration Number, MY registraion number is 35

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.59P

See similar textbooks

Similar questions

Two three-phase generators supply a three-phase load through separate three-phase lines. The load absorbs 30 kW at 0.8 power factor lagging. The line impedance is (1.4+j1.6) per phase between generator G1 and the load, and (0.8+j1) per phase between generator G2 and the load. If generator G1 supplies 15 kW at 0.8 poir factor lagging, with a terminal voltage of 460 V line-to-line, determine (a) the voltage at the load terminals. (b) the voltage at the terminals of generator G2, and (c) the real and reactive power supplied by generator G2. Assume balanced operation.
For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real power (state whether it is delivered or absorbed). (c) the reactive power (state whether delivered or absorbed). (d) the power factor (state whether lagging or leading). [Note: By convention the power factor cos() is positive. If | | is greater than 90, then the reference direction for current may be reversed, resulting in a positive value of cos() ].
A three-phase transmission line receiving end voltage is rated at 21 kV. A load of 1500 KW is connected at the receiving end of the transmission line 70 km long. The parameters of the transmission line are given by r = 0.09 Ω/km and x = 0.8 Ω/km. If the machine is working at 0.65 power factor lagging. Determine a) The series reactance of the transmission line b) Sending end line voltage c) Percentage Voltage regulation d) Percentage Efficiency
A 50 MVA, 15 kV three phase generator has a subtransient reactance of 0.2 p.u. The generator supplies two motors over a transmission line having transformers at both ends as shown in Fig. The motors have rated inputs of 30 MVA and 20 MVA both 30 kV with 0.15 p.u. subtransient reactance. The rating of the sending end transformer, Tr1 is 50 MVA, 11 kV / 132 kV with leakage reactance of 0.1 p.u. Transformer Tr2 at the receiving end has three single phase transformers and the rating of each individual transformer is 20 MVA , 33 / 76 kV with leakage reactance of 0.12 p.u. Series reactance of the line is 25 ohms. Draw the reactance diagram with all reactance marked in p.u. Select the generator rating as the base in the generator circuit.
The figure below shows a radial transmission system with a generator having a terminalvoltage of 95 KV at angle of10.5°. The load demand is 50 MW at a power factor of 0.88 lagging.Use a base of 128.4MVA . Instructions :round of to 2 decimal places. Calculate the following : 1.Load current (A) and Base current (A) 2Per unit impedance of transformer 2 and Per unit impedance of transformer 1.3.Per unit voltage of the generator. And Per unit voltage of the line. 4.Per unit voltage of the transformer 1 5.Per unit impedance of the line.6.Resistance of the transmission line when the load consumes full-load (Ω).
An Alternator having three-phase, 3-wire ABC system supplying an effective line voltage of 120 V, has an a three-impedances of 50 / 45 ohms in Delta connection. Assume that Vbc is the reference vector. In problem above, assuming that it is Wye connected load and VAN is the reference vector. Determine the total true power, reactive power, apparent power of the connected load. What is the capacity in Kva of synchronous generator if the connected load is 85%
S.4) the length of a three-phase power transmission line with a Nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/km. From the end of the line, a 56 MW star connected load is fed with a power coefficient of 0.8 back under a 64 kV interphase voltage. If the line head voltage of the transmission line is 69 kV, calculate the capacity and power of the star-connected capacitor to be shunted into the load connected to the end of the line.
Consider a simple power system: two generators (20MVA each at 13.2kV) running in parallel via a combined generator step-up transformer (rated at 30/33.3/36.7 MVA: ONAN/ONAF/ONAF cooling, 13.2 (Delta)/115 (Solidly Grounded Wye) kV). The sub-transmission line is 10.0mi long and rated at 115kV. Estimate (write the assumptions) the 3-phase bolted fault current at the end of the 115kV line.
PROBLEM 1. A three-phase transmission line is 100 km long. Its parameters are: z= (0.08 + j0.45) Ω/km y=j5 μS/km At the generating end it has a voltage of 115 kV L-L, and it is delivering a real power of PS= 51 MW and a reactive power of QS=31.6 MVARS. a. Find the parameters A,B,C and D. b. Determine the voltage and current at the receiving end. C. Calculate the regulation of the load node.
. A single-phase 12.47 KV transmission line several kilometers long feeds a load from a substation. The line has a resistance of 2 Ω and a reactance of 20 Ω. Instruments at the substation indicate that the active and reactive power inputs to the line are 4 MW and 3 Mvar, respectively. Calculate a. The line current b. The power factor at the substation c. The active power absorbed by the load d. The reactive power absorbed by the load e. The line voltage at the load
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
The length of a three-phase power transmission line with a nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/ km. At the end of the line, a 70 MVA star connected load with a power factor of 0.8 back under 69 kV interphase voltage is fed. Capacitive circuit element with a capacitance of 19.14 mikro F / phase is placed as shunt at the end of the transmission line. According to these given; a) Line head voltage and current, b) Calculate the active and reactive power per line.