For another steel, the fatigue limits are 10,000 cycles at 100 ksi, 50,000 cycles at 75 ksi, and 200,000 cycles at 62 ksi. If a component of this steel had been subjected to 5000 cycles at 100 ksi and 10,000 cycles at 75 ksi, how many additional cycles at 62 ksi would cause failure?

For another steel, the fatigue limits are 10,000 cycles at 100 ksi, 50,000 cycles at 75 ksi, and 200,000 cycles at 62 ksi. If a component of this steel had been subjected to 5000 cycles at 100 ksi and 10,000 cycles at 75 ksi, how many additional cycles at 62 ksi would cause failure?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2. Could the maximum shear stress theory and the Von Mises theory be used for copper and aluminum…

A: The maximum shear stress theory and the von mises theory are suitable for ductile material Since…

Q: A. Which parameters are used for passage from real multi-axial stress condition to one-axial…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: How does the carbon content in plane carbon steels affect the fracture toughness? Show this…

A: The fracture energy of a material is tested by using impact tests. The impact test measures the…

Q: Read the following statement regarding the influence of stress amplitude on the fatigue life of a…

A: As the stress amplitude is decreased while maintaining the mean stress less fluctuating stress is…

Q: How is Ductility specified?

A: Ductility is the property due to which an object is able to undergo large deformation before…

Q: The fatigue life of a certain steel was found to be 10* cycles at + 70 MPa and 10 cycles at + 50…

Q: Please elaborate the following: Typical stress-strain characteristics of steel in simple tension and…

A: Characteristics of Stress Strain Mechanical Properties

Q: vendor. It is supposed to have a tensile strength in the range 420 to 480 MPa. A Brinell hardness…

A: GivenBrinell hardness number=118Tensile strength range=420 to 480Mpa

Q: 3. For steels, the endurance limit is approximately half of the tensile strength, and the fatigue…

Q: From the following figure shows the tensile stress- strain curve for a plain-carbon steel. What is…

Q: Explain how fatigue failure occurs even if the material does not see overall stress levels higher…

A: A fatigue failure occurs in the material when the load is applied. When a load is applied to the…

Q: How can the ductility of material be specified?

A: Ductility is the material’s property to undergo large plastic deformation (permanent type) after the…

Q: Describe the fatigue tests by drawing all the necessary figures.

A: The above question is based on Fatigue Tests description.

Q: How does the stress/strain graph of a brittle material compare to a ductile material?

A: When a material is given to an external load, initially it experiences elastic deformation the…

Q: Using various tables, determine the specific strength (yield strength-to-density ratio) in unit of…

A: From the tables, obtain the yield strength and density for each material. To find: Specific…

Q: A component is subjected to a maximum cyclic stress of 750 MPa and a minimum of 70 MPa. The steel…

A: INTRODUCTION : Fatigue failure occurs when a recurrent or cyclic load causes cracks to develop and…

Q: Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and…

Q: Draw a stress-strain curve for a low carbon steel and explain important points and regions in…

A: Given Material Low Carbon Steel Find Stress-strain curve

Q: 6) The energy absorbed during the fracture of notched specimen is related to the area under the…

A: A stress-strain curve is a graphical measure of the mechanical properties of a material. It gives…

Q: a.) what happens to the yield strength of 250 maraging steel as the temperature increases? b.)…

A: (a) as the temperature increases the value of yield strength decreases.

Q: What are Ductile materials?

A: Ductility: It is a property of a material to elongate when tension or load is applied to it. In…

Q: If the required yield strength of a steel is 150 ksi, could SAE 1141 be used? Why?

A: Given :- Required yield strength of steel = 150 ksi To Find:- Suitable condition and SAE number…

Q: If the number of fatigue is smaller than the number of yield, would that be safe or not? and why?…

A: When machine parts are subjected to fluctuating loading it is called an fatigue, repeated or…

Q: A machine part is made of forged steel with Su MPa, S'e= 0.5 Su .Estimate the life cycles (L) for

A: Given Data⇒ Ultimate strength (Su)=630 MPaFatigue strength (S)=294 MPaEndurance strength (Se')=0.5Su…

Q: Enter your answer in units of MPa to 1 decimal plac

Q: For the same bar, if the engineering strains are 0.05 and 0.10 at engineering stresses of 200 and…

A: Given data: σ1=200 MPaσ2=220 MPae1=0.05e2=0.1

Q: n application requires ultimate tensile strength and yield strength of a steel at 110 ksi and 91…

A: I. Can SAE 1040 steel be selected for this application? Yes, It can be selected. Because the…

Q: A machine part is made of forged steel with Su = 630 MPa, S'= 0.5 Su .Estimate the life cycles (L)…

A: Given: The ultimate strength, Su = 630 MPa The endurance strength, S;e = 0.5Su The allowable…

Q: 11) If this material is subjected to a stress amplitude of 200MPA, how many cycles stress can the…

A: Given: From graph, The number of cycles at 210 MPa, N1 = 106 The number of cycles at 480 MPa, N2 =…

Q: Q12. How would a creep profile on a brittle material looks like?

A: How would be creep profile on a brittle material.

Q: Description of stress- strain curve in brittle metal

A: Stress strain curve: In strength of material or material science, this curve will shows the relation…

Q: (d) The yield strength values of pure aluminium (Al) and pure copper (Cu) are 25 MPa and 20 MPa,…

A: Solution: Given Data: σy,Al=25 MPaσy,Cu=20 MPaσy,AMM=200 MPaσy,CB=105 MPad=18.4 mm

Q: On a stress strain curve for structural steel, show various points like proportional limit, elastic…

A: Stress-Strain Curve for steel Point A is the proportional limit Point B is the elastic limit Point…

Q: For cast iron components, subjected to steady loading which of the following strength is considered…

A: It is also known that brittle materials do not show yield points under the application of tensile…

Q: What is the fatigue strength of 2014-T6 Aluminum (MPa) at 1E5 life?

A: To find : fatigue strength of 2014T6 Aluminum at 1E5 life

Q: How are the materials classified as ductile or brittle?

A: Ductile material When the material undergoes plastic deformation before the failure of the material…

Q: Value for 'D' in fatigue diagram above? (MPa) - {1DP} Your answer Value for 'E' in fatigue diagram…

A: A - yield strength B - alternating fatigue limit C - stress amplitude D - mean stress

Q: Table 4 shows the fatigue data of a ductile cast iron to be used for an automobile axle that rotates…

A: a)

Q: If a constant-stress load cycle is periodically interrupted by an anomalously large stress cycle,…

A: Fatigue lifetime Generally, it is a mechanical term used for the measurement of the lifespan of a…

Q: The fatigue life for a certain alloy at stress levels of σ1, σ2, and σ3 is 10,000, 50,000, and…

A: Given data: The number of cycle in level 1, n1 = 2500. The number of cycle in level 2, n2 = 10,000.…

Q: Using various tables, determine the specific strength (yield strength-to-density ratio) in unit of…

Q: 4) Draw a stress-strain curve for a low carbon steel and explain important points and regions in…

Question

I need the answer as soon as possible

For another steel, the fatigue limits are 10,000 cycles at 100 ksi, 50,000 cycles at
75 ksi, and 200,000 cycles at 62 ksi. If a component of this steel had been subjected
to 5000 cycles at 100 ksi and 10,000 cycles at 75 ksi, how many additional cycles
11.
at 62 ksi would cause failure?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An application requires ultimate tensile strength and yield strength ofa steel at 110 ksi and 91 ksi, respectively. Answer the following 4 questions:4.1. Can SAE 1040 steel be selected for this application?4.2. If “no” is the answer in Part I, the following Part II, III, and IV can beignored. If “yes” is the answer in Part I, which condition of SAE 1040 shouldbe selected?4.3. Why is that steel with the condition in part II selected?4.4. Is the selected steel brittle or ductile? and Why?
Draw the engineering stress-strain curve for low carbon steel and indicate the important points on the curve.
Draw a neat diagram of the relationship between fatigue stress and the number of loading cycles and show on it the shape of the curve for a material without an endurance limit.
An application requires ultimate tensile strength and yield strength ofa steel at 110 ksi and 91 ksi, respectively. Answer the following 4 questions: Can SAE 1040 steel be selected for this application? If “no” is the answer in Part I, the following Part II, III, and IV can beignored. If “yes” is the answer in Part I, which condition of SAE 1040 shouldbe selected? Why is that steel with the condition in part II selected? Is the selected steel brittle or ductile? and Why?
Draw a Stress/Strain graph of a mild tensile steel and identify the limit of proportionality and the yield point
A component is subjected to a maximum cyclic stress of 750 MPa and a minimum of 70 MPa. The steelfrom which it is manufactured has an ultimate tensile strength, σu, of 1050 MPa and a measured endurancelimit, σe, of 400 MPa. The fully reversed stress at 1000 cycles is 750 MPa. Using both the Goodman and Gerbermean stress correction procedures, calculate the component life.
The fatigue life for a certain alloy at stress levels of σ1, σ2, and σ3 is 10,000, 50,000, and 500,000 cycles, respectively. If a component of this material is subjected to 2500 cycles of σ1 and 10,000 cycles of σ2, estimate the remaining lifetime in association with cyclic stresses at a level of σ3.
For the given fluctuating fatigue koad, the values of stress amplitude and stress ratio are.
A machine part is made of forged steel with Sy = 630 MPa, S'== 0.5 S, .Estimate the life cycles (L) for a fatigue strength of 294 MPa. For 103 cycles, take Sf=0.9 S,
Using various tables, determine the specific strength (yield strength-to-density ratio) in unit of kN⋅m/kg for AISI 1015 hot-rolled steel, 7075-T6 aluminum alloy, Ti-0.2 Pd titanium alloy, and ASTM No. 60 gray cast iron.
Question: Suppose that the fatigue data for the steel alloy in Problem 9.12 were taken for bending-rotating tests, and that a rod of this alloy is to be used for an automobile axle that rotates at an average rotational velocity of 600 revolutions per minute. Give the maximum lifetimes of continuous driving that are allowable for the following stress levels: (a) 450 MPa (65,000 psi), (b) 380 MPa (55,000 psi), (c) 310 MPa (45,000 psi), and (d) 275 MPa (40,000 psi). Reference: Problem 9.12 is listed below (only use for reference but does not need to be solved). The tensile strength of brittle materials may be determined using a variation of Equation 9.1. Compute the critical crack tip radius for an Al2O3 specimen that experiences tensile fracture at an applied stress of 275 MPa (40,000 psi). Assume the acritical surface crack length of 2 x 10-3 mm and theoretical fracture strength of E/10, where E is the modulus of elasticity.
If a constant-stress load cycle is periodically interrupted by an anomalously large stress cycle, does the overall fatigue lifetime of the component remain the same, diminish, or increase?