For each piece of glassware measure the density of water in triplicate (three times). Why repeat the procedure multiple times for each piece of glassware? Running the measurement in triplicate increases the precision of our results and reduces the impact of a single outlier result. The experiment would be too short if you only ran each trial once The first two trials act as practice, and the final trial will give you the true result. Running the measurement in triplicate increases the accuracy of our results and reduces the impact of a single outlier result

For each piece of glassware measure the density of water in triplicate (three times). Why repeat the procedure multiple times for each piece of glassware? Running the measurement in triplicate increases the precision of our results and reduces the impact of a single outlier result. The experiment would be too short if you only ran each trial once The first two trials act as practice, and the final trial will give you the true result. Running the measurement in triplicate increases the accuracy of our results and reduces the impact of a single outlier result

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter1: The Nature Of Chemistry

Section: Chapter Questions

Problem 85QRT

See similar textbooks

Similar questions

If you repeat the same measurement many times, will you always obtain exactly the same result? Why or why not? What factors influence the repeatability of a measurement?
In an experiment a student used a 50 mL volumetric flask to prepare her copper solution but in calculations she used 100 mL as the sample volume. What effect will this error have on the final result? Will the calculated result be high of low?
In order to find the density of a solution of unknown density, 10 mL of solution was drawn into a clean and dry beaker three times with a pipette and weighed and the weighing results were found to be 65.1452 g, 64.9982 g, 65.1027 g. Calculate the density of the solution and the standard deviation of the measurements, since the empty weight of the beaker is 52.2461 g.
The Calcium content of a banana sample was homogenized and measured. Are the results comparable? Do they have the same precision? Please use data given.
The radius of a copper (Cu) atom is roughly 1.3 × 10−10 m. How many times can you divide evenly a 223.3−cm long piece of copper wire until it is reduced to two separate copper atoms? (Assume there are appropriate tools for this procedure and that copper atoms are lined up in a straight line, in contact with each other. Round off your answer to an integer.)
What is the smallest mass that we can measure on an analytical balance that has a tolerance of ±0.1 mg, if the relative error must be less than 0.1%?
Employ the method of dimensional analysis to convert 1 cubic yard to tonnes of water. Assume a density of water of 0.998 g/mL. To ensure that the question is marked as correct, arrange the units so that the top unit cancels with the bottom unit in the next step. Note that some of the quantities have been filled in for you.
1. All answers to be entered via short answer are in the NUMERICAL FORMAT and presented up to the 3rd decimal place. ADD TRAILING ZEROS if necessary, to complete your answer. NO NEED TO INCLUDE THE UNIT for now.For uniformity of answers, please be guided by the following examples:- If your answer is 5.627594, enter 5.628- If your answer is 3.129934, enter 3.130- If your answer is 8.38, enter 8.380- If your answer is 1.2, enter 1.200- If your answer is 25, enter 25.000- If your answer is less than the value of 1, always place a zero before the decimal point (E.g.: if 0.5, enter 0.500)2. In cases for answers in the EXPONENTIAL FORMAT, please be guided by the following examples and format:- Do not convert your answer to decimal format- If your answer from the calculator is 1.23454566 x 10E-4, enter 1.235x10^-4 (no spaces in between)- If your answer from the calculator is 7.379566 x 10E-5, enter 7.38x10^-5 (no spaces in between)3. The ATOMIC MASSES should be rounded to the NEAREST WHOLE…
but the answer is false... so it will affect precision and accuracy? I know that this error belongs to systematic error, so systematic error affect precision?
A volumetric flask that is to be used to measure volume is supposed to be marked at 10.00 ml but is actually marked at 9.95 ml. This error affects its precision. True or false? please explain
The diameter of a copper (Cu) atom is roughly 1.3 x10-10 m. How many times can you divide evenly apiece of 10-cm copper wire until it is reduced to twoseparate copper atoms? (Assume there are appropriate tools for this procedure and that copper atoms arelined up in a straight line, in contact with each other.)Round off your answer to an integer.
To prepare olives for consumption and remove their bitterness, powdered soda (sodium hydroxide, NaOH) is usually used in the industry, which is added to the water in which the olives are found (this method should not be used at home if we had olive trees because soda is highly corrosive and very dangerous, in this case we should use table salt). Normally 1 kilogram of soda is added for every 3 liters of water (weighing 3 kg, remember that the density of water is 1 g/mL).Thus, 4 kg of solution were obtained, and the density of this solution was determined experimentally to be 1.25 g/mL. a) Calculate what volume of solution is obtained. (Remember that d = m/V). b) What will be the concentration of that solution expressed in grams of solute dissolved in each liter of solution? c) What will be the concentration expressed in % by mass (or weight)? • If we separate a ladle (100 mL) of that solution. d) What will be the concentration of soda in the liquid in the ladle? e) How many grams of…