For force P on the handle of the toggle clamp the clamping force C increases to large values as the angle θ decreases. For P =  21 lb find the relationship between C and θ and plot it as a function of θ from θ =  4° to θ =  42°. Knowing that the shaft slides freely in its guide, answer the questions in lbs.

Q: Before solving the question: Consider your 10 digits student number as ##########. Then, assign the…

A: Draw the free body diagram of the given arrangement: P=-100+akP=-100+0kP=-100 k N…

Q: Q12/ A shaft carries four masses A, B, C and D of magnitude 200 kg. 300 kg. 400 kg and 200 kg…

A: Given, Mass of A is m1=200 kg Mass of B is m2 =300 kg Mass of C is m3=400 kg Mass of D is m4=200 kg…

Q: A band brake embraces a drum such that one end of the band is attached to the fulcrum pin and the…

A:

Q: A lO-kN car and 5-kN hoist are supported 1.8 m above the floor by a cylinder with a 300-mm bore .…

A: Total force acting on the cylinder,F=10+5=15kN=15000N Area of the bore of the cylinder,A=π/4*(d^2)…

Q: STATICS 1. Three bars, hinged at A and D and pinned at B and C as shown, form a four-link mechanism.…

A: Dear student, The above three questions are completely different not interconnected with each other.…

Q: Question 2 The wheel A and a block B are connected by a cable. The coefficient of friction of the…

A: Write the given value using suitable variables. Here r1 signifies small wheel radius, r2 signifies…

Q: A 120-lb cabinet is mounted on casters that can be locked to prevent their rotation. The coefficient…

A:

Q: A 120 lb box sits on top of the 60 lb back cover of a pickup truck. Determine the vertical and…

A:

Q: A semicircular rod is loaded as shown. Determine the internal forces at point J.

A: The free-body diagram of the section will be given as follows,

Q: 13. For Problems 1 to 3. Three forces were applied to the horizontal beam of negligible mass, as…

A:

Q: All dimensions, applied loads P and reactions at A and I are known. Determine the following…

A: It is required to choose correct answer

Q: 6. 2) The uniform slender 14-kg bar of length /= 3.2 m rests on smooth surfaces but starts to slide…

A: To find: The normal force at point A. Given: The mass of the slender bar is m=14 kg. The length of…

Q: 07 The 180-1lb tree surgeon lowers himself wit rope over a horizontal limb of the tree. If the c…

A: Givenμ=0.60θ=180°

Q: * :Q7/ The value of reaction RA is Point D 10 kN Point E h-200 mm 50 mm 2 kN 75 mm 2m 3m Point F…

A:

Q: A) what direction does friction act on at point A? B) a ladder weighs 20lbs on a rough floor (us=.8)…

A: To determine the force P, we will use the following equations- 1. Summation of all vertical forces…

Q: The bar AC is supported by a joint at A and a pin B that is free to slide in the same direction…

A: Given; Length, L1 = 2.7 m Length, L2 = 1.7 m Angle, α = 13o Angle, θ = 25o The force, P = 68 kN

Q: A 100-m, 10 N uniform rods carries 20-N and 30-N weights suspended at its ends, as shown. Where…

A: Given data,  P1= 20 N  P2= 30 N  Length of rod is L= 100 m

Q: Question 8 The ladder AB, of mass 30 kg, is positioned as shown. What is the B direction of the…

A: The direction of friction is opposite to the direction of movement.

Q: A force F of magnitude 60 N is applied to the gear

A:

Q: The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical…

A: according to the given details in the question. WE NEED TO FIND-OUT ANGLE THETA

Q: hy isn't anyone answering this?? A 50 lb block drops onto the top of a 25 lb spring scale. The block…

A: Given:m=50 lbms=25 lbh=6 ft =72 ink=100 lb/in

Q: A flat belt connects pulley A to pulley B. The coefficients of friction are μs = 0.25 and μk = 0.20…

A:

Q: The uniform bar is at rest on a smooth half-sphere with radius R = b / 2. In A there is a ball joint…

A:

Q: H0.60 1. The compound pulley shown weighs 5 KN and has a centroidal radius of gyration of 2 meters.…

A:

Q: A four-link mechanism is subjected to the following external forces determine the shaft torque T2 on…

A: Link 3 and 4 are both two force member  Therefore f4 can be along BC and f43 along  oc=A3×F43 is to…

Q: The mass center G of the 1300-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: D 4.8 in. C 1.84 in. B 0.8 in. 5.6 in. 2.4 in. 1.6 in. Fig. P4.43 and P4.44 4.44 A parabolic slot…

A:

Q: The frictional resistance of a thrust bearing decreases as the shaft and bearing surfaces wear out.…

A: Given data: The distance of small area on the bearing is r. The couple is M.

Q: QUESTION 4 Three identical blocks of mass m on a frictionless surface are connected by massless taut…

A: The Newton second law state that : ∑Fx=ma from the free body diagram of the rightmost block:…

Q: The system below is in balance. Knowing that the weight of the bucket is 900 N, determine…

A: Option 5 is correct.

Q: A single-pneumatic cylinder has an internal diameter of 50mm and a piston which is required to exert…

A: Given data: internal diameter (d) = 50mm Force (F) = 1.5 kN  Need to determine the gauge pressure is…

Q: A 580.2N horizontal steel shaft is suspended by a vertical cable from A and by a second cable BC…

A:

Q: - 24 in.- D P 10 in. B C y

A:

Q: A lamp of mass m is suspended from two cables of unequal length as shown to the right. Which of the…

A:

Q: A person's arm is used for ergonomic studies. If the distance of the AB, BC, and CD segments are…

A: The loading diagram of the given ergonomics study considered is as shown below:   Find the…

Q: A pneumatic system is operated at a pressure of 1000 kPa. What diameter cylinder will be  required…

A: Pressure or intensity of Pressure may be defined as the force exerted on a unit area. Thus, p=dFdA,…

Q: 1418. A weight is dropped from a position just above, but not touching, a spring. Show that the…

A: For gradual loading of spring:δst=PKHere,P=Load/Weight on springK=Spring constantδst=static…

Q: The crate pulled by a man as shown weighs 200 N. Supposed that the static friction coefficient…

A: Static equations:

Q: The bucket of the front-end loader shown carries a 3200-lb load. The motion of the bucket is…

A: Let us draw the FBD of the bucket Take Moment about D FAB(16 in)-1600 lb(15 in)=0 FAB = 1500 lb

Q: Question 2 The wheel A and a block B are connected by a cable. The coefficient of friction of the…

A:

Q: 30 300 mm Fig.(Q1) Q1:The 100 kg wheel rests on a rough surface and bears against the roller A when…

A: Given Data: Wheel Mass m=100 Kg Applied Couple M=60 N-m Radius of wheel r=300 mm=0.3 m Angle with…

Q: The 283 kg horizontal steel bar is suspended by the three springs. The stretch of each spring is 126…

A:

Q: A block weighing 200 N is just moved on a rough horizontal plane by a pull of 90 Newton acting at an…

A: Let us draw the free body diagram the weight is acts downward and normal reaction at upward And the…

Q: F1 926N 1.50m 3.70 m 2.60 m 69.3° 71.1° 56.6° F2 F3

A:

Q: True or False 1. The load, P, in the experiment on the mechanical properties of chocolate, can be…

A: True or False 1. The load, P, in the experiment on the mechanical properties of chocolate, can be…

Q: In the mechanism below, neglect the inertias of all the links and determine the cable tension force…

A: given data; →mass (M)=1.424kg→FC=CD=0.8→FD=FC+CD      =0.8+0.8       =1.6m→tension in cable=T→lets…

Q: The figure below shows the essential parts of a hydraulic brake system. The area of the piston in…

A:

Q: To test the deflection on a uniform 100-kg beam, a boy of who weighs 50 kg exerts a pull of 150N on…

A: Given data: The mass of the beam is M=100 kg The mass of the boy is mB=50 kg The tension in the rope…

Q: The drive belt on a vintage sander transmits ½ hp to a pulley that has a diameter of d = 4 in.…

A: Given   data as per questiondiameter  =4 in=0.1016 mPower=12hp=372.85 wattN=1450…

Q: The torque exerted by a shaft in a Prony brake with an arm length of 1.85-feet and the scale reading…

A: force(F)=250lb Arm length(d)=1.85ft