A four-link mechanism is subjected to the following external forces determine the shaft torque T2 on the input link AB for static equilibrium of the mechanism. Also find the forces on the bearings A. B. C and D. AB = 500 mm, BC 660 mm, CD 560 mm, AD =1000 mm F2= 80 N, F3= 144 N, F4= 60N %3D - 297- Bp 58 Draw the mechanism diagram with a suitable scale (say, SM = 0.1 mm/mm) as shown 325 373 73.5 60 (mm)

A four-link mechanism is subjected to the following external forces determine the shaft torque T2 on the input link AB for static equilibrium of the mechanism. Also find the forces on the bearings A. B. C and D. AB = 500 mm, BC 660 mm, CD 560 mm, AD =1000 mm F2= 80 N, F3= 144 N, F4= 60N %3D - 297- Bp 58 Draw the mechanism diagram with a suitable scale (say, SM = 0.1 mm/mm) as shown 325 373 73.5 60 (mm)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.59P: The weight of the uniform bar AB is W. The stiffness of the ideal spring attached to B is k, and the...

See similar textbooks

Similar questions

The uniform bar AB of weight W and length L is pinned to a sliding collar at A and to the sliding rod BD at B. The spring wound around rod BD has a stiffness k and is undeformed when rod AB is in the position =0. Determine the expression for the angle (other than =90 ) at equilibrium and investigate the stability of equilibrium for this position.
Find the stable equilibrium position of the system described in Prob. 10.56 if m = 2.06 kg.
The shaft pulley system has a universal joint at point 0. So it is supported by a slide at point A bearing and fixed support at point C. There is a mass of 12kg on the pulley and subject to the belt tensions but the mass of the shaft is negligible. a) what is the static equilibrium equations for the assembly. b) draw the FBD of the assembly. c) show the assembly and the FBD for the components
Now that we've found the force F12, which equilibrium equation will allow us to find the force F13 between joint 1 and 3? Question 3 options: Sum of torques = 0 Sum of horizontal forces = 0 Sum of vertical forces = 0
Use the method of sections to find the true magnitude and direction in bar DB of the truss. Hint (Joint C is in equilibrium)
A 120-lb weight is attached to the cable that is wrapped around the 50-lb homogeneous drum. Theshaft attached to the drum is supported by a thrust bearing at A and a slider bearing at B. The drum iskept in equilibrium by the vertical force P acting on the handle of the crank. Determine P and thereactions at A and B. Neglect the weights of the crank and the shaft. Provide a free-body-diagram.
Crank connecting rod in Figure-1crank and connecting rods in the mechanismare the same length; AB = BC = L andBF=FC. One end to point B, the otherfrictionless with the tip horizontally.connected to movable point Dthe stiffness of the spring is k (N/m) when =90the spring is not elongated. spring mechanismforce, R1 and R2 forces and Mstatic under the influence of momentis in balance. The principle of virtual worksstatic balance of the mechanism by applyinggiving the theta angle corresponding to the positionget a relation andthe last of your student number from the table.appropriate values according to the numberCalculate the theta angle using M= -400Nm R1=300N R2=200N L=1,3m k=500N/m
When F = 300 N with Θ = 40°, what is the maximum value which P may have for static equilibrium? Neglect the weight of the structure compared with the applied loads.
The upper end of the bar of a problem is now leaned against a non vertical wall. Determine the minimum value of the angle θ for which equilibrium is possible for μs = 0.25 and for μs = 0.50
The weight of the limb is W=15 lbs.The contact of foot with the ground can be modeled as a pin/hinge here. Determine the reaction force of the ground and the reaction at the knee joint and its direction/angle θ. Note: use the thee force member condition to find the angle of FK.Q4.As it’s been shown in the below figure,a person is using an exercise machine. Points A and B correspond to the shoulder and elbow joints, respectively. Relative to the person, the upper arm (AB) is extended toward the left (x-direction) and the lower arm (BC) is extended forward (z-direction). At this instant, the person is holding a handle that is connected by a cable to a suspending weight. The weight applies an upward (in the y-direction) force with magnitude F on the arm at point C. The lengths of the upper arm and lower arm are AB̅̅̅̅= 20cm and BC̅̅̅̅= 25cm, respectively, and the magnitude of the applied force is F = 400 N.Determine the components of reaction developed at the shoulder joint A When the…
3-5.4. Determine the value of T if the force system shown in Fig. P-3-5.4 is in equilibrium. Suggestion: Use a moment summation.
note: this is for engineering Question: A uniform pole 20 ft long and weighing 80 lbs is carried by two men A and B, one at each end of the pole. a. Draw the figure b. Draw the force diagram c. Write the equations for the 1 st Condition and for the 2 nd Condition of equilibrium