please answer neatly and show complete solution For questions 1A, 1B, and 1C. The figure below shows the reinforced concretebeam AB of a tourist lookout at the free end. Its weight per unit length is2500N/m, and the beam rests on two pillars at A and B, with no fixed connection.1A. Assuming the beam is uniform, which of the following gives the absolutemaximum shear? *8.0mB6.0mFigure for Questions 1A, 1B. and 10O 7500N10000N12500NO 22500N1B. What is the value of the absolute maximum moment? *11250NM20000NM31250NM22500NM1C. Reinforcing steel bars [shown by the bold lines] are used in the concretebeam in the lookout as shown in the diagram below, which of the followingdiagrams best shows the placements of these reinforcements? *Option 1Option 2O Option 3O Option 4O O O O

Answered: Image /qna-images/answer/038f6b80-bc04-40c6-8a40-4d3250297316.jpg

For questions 1A, 1B, and 1C. The figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight per unit length is 2500N/m, and the beam rests on two pillars at A and B, with no fixed connection. 1A. Assuming the beam is uniform, which of the following gives the absolute maximum shear? * A 8.0m B 6.0m Figure for Questions 1A, 1B, and 10 7500N 10000N 12500N 22500N

For questions 1A, 1B, and 1C. The figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight per unit length is 2500N/m, and the beam rests on two pillars at A and B, with no fixed connection. 1A. Assuming the beam is uniform, which of the following gives the absolute maximum shear? * A 8.0m B 6.0m Figure for Questions 1A, 1B, and 10 7500N 10000N 12500N 22500N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
QUESTION-1: Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
The shear capacity V if a steel wide flange section, 600 mm deep whose web is 9 mm thick, is closest to: Assume fy = 200 MPa. Take FV = 0.4 Fy a. 645 kN b. 413 kN c. 507 kN d. 432 kN
A column is made of steel and concrete, if the normal forces on steel and concrete are 6.8kip and 145kip and the allowable stresses of steel and concrete are 36ksi and 5.5ksi, and the cross sectional areas of steel and concrete are 0.3068in^2 and 45.5456in^2 respectively, determine whether the still or concrete will fail when given a yield factor of safety of 1.69
The reinforced concrete column isreinforced with 6 – 28 mm Ø bars as shown. Steel yield strength fy = 414 MPa and concrete strength fc’ = 21 MPa. Determine the nominal balanced load.a. 1721.252 kN c. 1821.225 kNb. 1921.253 kN d. 1521.522 KNDetermine the nominal balanced eccentricity.a. 362.544 mm c. 352.544 mmb. 372.544 mm d. 382.544 mmDetermine the nominal balanced moment.a. 677.326 kN.m. c. 777.321 kN.m.b. 312.852 kN.m d. 563.285 kN.m. Please answer asap. Thanks
If FB = 560 N and FC = 700 N, determine themagnitude and coordinate direction angles of the resultantforce acting on the flag pole.
What will be the value of the shear force at the fixed end A, at free end B and at point C for the bearn shown below?
Find the Maximum Shear andMoment.? can you solve in 20 mins?
The reinforced concrete column is reinforced with 6 – 28 mm Ø bars as shown. Steel yield strength fy = 414 MPa and concrete strength fc’ = 21 MPa.1. Determine the nominal balanced load.a. 1721.252 kN c. 1821.225 kNb. 1921.253 kN d. 1521.522 KN2. Determine the nominal balanced eccentricity.a. 362.544 mm c. 352.544 mmb. 372.544 mm d. 382.544 mm3. Determine the nominal balanced moment.a. 677.326 kN.m. c. 777.321 kN.m.b. 312.852 kN.m d. 563.285 kN.m.
Replace the loading (Figure 1) by an equivalent resultant force and couple moment at point O. Suppose that F1={8i−2k}kN and F2={−4i+5j−2k}kN. Part A Part complete Determine the resultant force. Enter the x, y, and z components of the force in kilonewtons to three significant figures separated by commas. Part B Determine the equivalent resultant couple moment about point O. Enter the x, y, and z components of the moment in kilonewton-meters to three significant figures separated by commas.
The bent bar shown is subjected to 3 forces shown. Replace these forces with an equivalent couple M and single force F at point A. Show solution to answers M = 21.8 kN-m, cw Fv = 12.03 kN, D FH = 1.60 kN, R