For the arrangement shown in figure, find the force F needed to cause impending motion F to 3kN wei surfaces of contact being u=0.3. What is the tension in the cable? 30° 2kN- F 3kN ANS: || kN ( two decimal places)

For the arrangement shown in figure, find the force F needed to cause impending motion F to 3kN wei surfaces of contact being u=0.3. What is the tension in the cable? 30° 2kN- F 3kN ANS: || kN ( two decimal places)

Name: For the arrangement shown in figure, find the force F needed to cause
Uploaded: 2024-03-20T06:56:46.000Z
Channel: Bartleby
Description: For the arrangement shown in figure, find the force F needed to cause impending motion F to 3kN weisurfaces of contact being u=0.3. What is the tension in the cable?30°2kN-F3kNANS: ||kN ( two decimal places)

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter6: Applications Of Newton's Laws

Section: Chapter Questions

Problem 26P: Find the tension in each of the three cables supporting the traffic light if it weighs

See similar textbooks

Similar questions

If the hanging block is 5 kg, how do you find the tension in each rope?
An elevator with a mass of 4850kg is to be designed so that the max acceleration is 0.068g. What are the maximum and minimum forces the motor should exert on the supporting cable? I know the answers are rounded to 50800N (max) and 44300N(min), but I have no clue how to get those numbers. Please show ALL alegbraic steps. Thanks!
The reading on the tension protractor on the left is 1.6N, 115°. What is the x-component of the tension on the left cord?
Assume the three blocks m1 = 1.0 kg, m2 = 2.0 kg m3 = 3.5 kg portrayed in the figure below The coefficient of friction is .25 and the F acting on m3 is 40 Newtons. Find the tension of the rope?
A push and a pull of magnitude F1=3.9 N and F2=5.8 N act on a block of weight 11 N resting and not moving on a rough surface as shown in the figure linked below. The push F1 is horizontal, while the pull F2 acts at angle θ=46 deg with the horizontal How large is the friction force exerted by the surface on the block?
Two blocks connected by a string are pulled across a horizontal surface by a force applied to one of the blocks, as shown. The coefficient of kinetic friction between the blocks and the surface is 0.25. If each block has an acceleration of 2.0 m/s2to the right, what is the magnitude F of the applied force?
A 25-kg block is pulled by a horizontal force. The supporting rope can withstand a maximum tension force of 620 N. To what maximum angle, theta, can the block be pulled without the rope breaking?
How do you find the tension in each rope if there's a hanging mass of 20kg and it's in an equilibrium?
Three forces act on a point. : 3 N at 0 degrees, 4 N at 90 degrees, and 5 N at 217 degrees. What is the resultant? Select one: 4.4 N, 179.4 degrees 1.4 N, 135 degrees 1.4 N, 315 degrees 4.4 N, 0.59 degrees
Find and plot the equillbrant for the following forces (use protractor and ruler) 4. Fa= 93.0 N at 53.0 west of north 5. Fs = 65 N at 21.0 south of west 6. Fs= 102 N at 15.0 west of south
An elevator (mass 4850 kg) is to be designed so that the maximum acceleration is 0.0680g. What are the maximum and minimum forces the motor should exert on the supporting cable? In solving it , 1 was added to the acceleration when it was going up and subtracted when it is going down and I am confused on why.
The block shown is pulled across the horizontal surface at a constant speed by the force shown. If M = 6.0 kg, F = 15 N and θ = 37°, what is the coefficient of kinetic friction between the block and the horizontal surface?