For the assembly shown below, the beam AB weighing 100 Ibs is loaded with force P = 200 Ibs. A frictionless pulley with radius "r' and weighing 80 Ibs is attached at the end of the beam at point B, supported with two ropes inclined at angles x and y points at C and D. If a = 2 ft, b = 3 ft, angles x & y are 30 deg. and 40 deg. respectively and radius "r' is 6 inches, Which of the following most nearly gives the reaction at B in Ibs. * Choose mte A B

For the assembly shown below, the beam AB weighing 100 Ibs is loaded with force P = 200 Ibs. A frictionless pulley with radius "r' and weighing 80 Ibs is attached at the end of the beam at point B, supported with two ropes inclined at angles x and y points at C and D. If a = 2 ft, b = 3 ft, angles x & y are 30 deg. and 40 deg. respectively and radius "r' is 6 inches, Which of the following most nearly gives the reaction at B in Ibs. * Choose mte A B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Show your solution to the problem and use 2 decimal places in your final answer. Considering the diagram shown, determine the shear and moment at the supports of the continuous beam if DL = 3kN/m and LL=5 kN/m, L1= 5m, L2= 6m, and L3= 5m.
Calculate the force on Member CH in Kips by the method of sections. if the given 30kip load at joint J and 25kip loads at joints B, C, D, E from the figure are replaced by 85kip and 108kip loads respectively. Express your answer in 2 decimal places. Include (-) negative sign if the force is compression.
Question 1) F=20 kN single load, M=23 kN.m moment and w=19 kN/m distributed load are acting on the beam whose loading condition is given in the figure . The length L is also given as L=5 m . The cross-sectional properties of the beam are; body height y g =248 mm , body thickness x g =12 mm , flange width x f = 196 mm , flange height y f = 20 mm . Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question1-A ) Find the normal force (N C ) at point C. ( Write your result in kN .) Question1-B ) Find the shear force (V C ) at point C. ( Write your result in kN .) Question1-C ) Find the bending moment ( MC) at point C. ( Write your result in kN.m. )
Consider a horizontal, uniform beam that extends from x = 0 m to x = 2.5 m. The beam is supported at each end by two strings which exert forces directly upward. There is a downward force per length on the beam given by dF/dx = 488 x (2.5 - x) (N/m), which includes any weight force on the beam. Calculate the tension in the rope attached to the right end of the beam.
A girder supports four concentrated loads of 800lb as shown in the figure. Assume the support at A is pin and B is a roller. Answer the following: Compute the internal shear force, normal force and moment at a point 20ft from point A. Assign this point as point C. Determine the shear and moment in the girder as a function of x, where 12ft < x < 24 ft. Compute the maximum shear moment in the girder. (Draw the shear and moment diagram)
Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please
Determine the shear force 9.8 ft to the right of point A for the beam shown belowif T = 1059 lb ft, W = 178 lb/ft, a = 5.6 ft, b = 3.59 ft, and c = 3.94 ft. Round of the final answer (in lb) to four decimal places.
Determine the magnitude of force (kN) in member AC if F=2406 N , a=3.2m , b=7.3m and c=4.9m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
Given: fy = 345 Mpaf'c = 28 Mpa Determine the moment arm of the beam in mm in 3 decimal places.
Draw the Normal Force (N), Shear Force (T) and Bending Moment (M) diagrams of the beam whose span and loading condition are given in the figure. H(t)2 M (tm)15 q1(t/m)16 q2(t/m) 19 P(ton)15 a(m)4
Determine the magnitude (N) of the force in member BC if F=335N , a=0.42m, b=2.08m, r=1.09m and d=23.39degrees. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
Knowing that w is 680 lb/ft, determine the internal moment in the beam at point C using the sign convention for internal moment. Express your answer in ft*lb to nearest whole ft*lb