For the circuit below with R1 = 10Ω, R2 = 12Ω, X1 =9, A = 44, B = -16 degrees, calculate the reactive power supplied by the source to the circuit in VARS. For the circuit below with R₁ = 10N, R₂ = 12N, X₁ =9, A = 44, B = -16degrees, calculate the reactive power supplied by the source to the circuitin VARS. Please give the answer below with noR₁wwwA

The phasor problem is solved as shown below.

For the circuit below with R₁ = 10N, R₂ = 12N, X₁ =9, A = 44, B = -16 degrees, calculate the reactive power supplied by the source to the circuit in VARS. Please give the answer below with no creits A

For the circuit below with R₁ = 10N, R₂ = 12N, X₁ =9, A = 44, B = -16 degrees, calculate the reactive power supplied by the source to the circuit in VARS. Please give the answer below with no creits A

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 9PP: In an R-L parallel circuit, ET=240 volts, R=560 R = 560 2, and XL=330. Find reactive power.

See similar textbooks

Related questions

Q: The circuit has an RMS secondary voltage of 22.16 volts. One of the diodes is broken. Considering…

A: Given data Primary voltage, VpRMS=120 V Secondary voltage, VsRMS=22.16 V Supply frequency, f=60 Hz…

Q: For the transistor amplifier shown in the picture, find the value of the quiescent output voltage…

Q: The input characteristics of the common-emitter configuration show the relation between the emitter…

A: given common emitter configuration

Q: For the circuit below, when the switch is at point b, the output voltage Vo is equal to R Vio- b O…

Q: 2. The rotor resistance per phase of a 4-pole, 50 Hz, 3-phase induction motor are 0.025 and 0.125…

Q: Create a simple/personalized series and parallel resistors and supply them with a voltage. Resistors…

A: To draw the combination of a series -parallel circuit by using atleast non-identical resistors:

Q: A parallel-plate air capacitor with a capacitance of 257 PF has a charge of magnitude 0.140 μC on…

Q: Required information Consider the given circuit where = 6 mA. An ammeter with internal resistance R¡…

A: Current in series elements are equal. The ammeter is connected in series. The voltmeter is…

Q: Question 4 Consider an LTI system with frequency response: 1+e-j2 te -j4w H(ej") = -π<ωΣπ 1+2e-j40…

Q: The power input to a 2000 V, 50 Hz, three-phase motor running on full-load at an efficiency of 90%…

A: A motor is tested using two wattmeter's method it is asked to find the input, power factor, line…

Q: 2.2 Suppose a sinusoidal voltage of ±10 V with a frequency of 500 HZ is to be displayed on an…

A: The given problem is from measurements and instrumentation. The detailed solution is given in the…

Q: If the current density in a co b. с 0.138 V/m Not enough informat ed. 7.25 V/m 4.64 x 10¹4 V/m

A: Given data, Conductivity is given as, σ=5.8×107 S/m. Current density is given J=8×106 A/m2.

Q: 2. Label the mesh currents and write the equations for the mesh currents and solve for them. ww 10 5…

Q: 6. Refer again to Figure 9-19. If R1 were shorted, the a. circuit current would increase. b current…

A: To answer the questions

Q: QUESTION 8. Find the piecewise-linear equivalent circuit for the diode of Fig. 1.15. Use a…

A: Given data Non-linear graph of diode current Vs diode voltage is given in the problem. The cutt-off…

Q: Example: A 32/4 dipole is radiating into free-space. Input power to the dipole is 100 W. Assuming an…

A: The given problem is from antenna theory. The detailed solution is given in the next step

Q: 3. Solve for the current in the 2 ohm resistor in the figure shown + 20 V a C 6n 40 10 V V₁ 0 + F 50…

Q: A transformer with ratio 6:3 is powered by a voltage source with 388 V ac and an internal source…

A: In this question We need to determine the primary side current of the transformer. We know V1 /V2 =…

Q: 4.(a) Briefly describe the four common principles of operation of sensors. (b) With the aid of a…

A: Solution of question (4.a); It is asked to describe briefly the four common principles of operation…

Q: load of 500 kVA operates on 1100 V, 50 Hz mains with power factor of 0.6 lagging. It is required to…

Q: A balanced twelve-phase mesh connected load has a line current of magnitude 10.3 A. What is the…

A: The question is about phase current.

Q: An embedded system that triggers an actuator only when a sensor senses something is call continuous…

A: When a sensor senses something, then the embedded system triggers the actuator. It means that the…

Q: 2. Find vo(t) for t> 0 in the circuit below. The switch opens at t = 0.

A: In the given questions we need to calculate the output voltage expression. This questions belong to…

Q: Figura 4 R₁ www (a) R₂ R3 42 R₁ 34₂ (b) R₂ www R3

A: given circuit problem.we have to calculate time constant

Q: 2. Solving ODE with Laplace transform For the following ODE, 4y"+y'=2[u(t − 1) − u(t − 2)] with y…

A: Given: ODE, 4y"+y'=2[u(t-1)-u(t-2)], with initial conditions, y(0)=1, y'(0)=0, To find: a) Laplace…

Q: Required information The circuit shows a two-op-amp instrumentation amplifier. R4 www ਪ R₂ R3 www…

Q: 1. Laplace transform and its inverse -5t te a) Consider f(t) = To 05 70(1-7) i) Write f(t) in terms…

Q: If C 45 µF, determine the equivalent capacitance for the combination shown. a) 17.0 µF, b) 30.0 µF,…

Q: Required information Problem 05.001 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS The equivalent…

A: We need to find out the output impedance for given circuit.

Q: Q8: An ideal MOS capacitor with an n+ polysilicon gate has a silicon dioxide thickness of tox = 12…

A: Given, Silicon dioxide thickness, tox=12 nm=120AoP-type doped, Na=1016 cm-3

Q: Question 19 While some ideal antennas are described as omnidirectional or isotropic, real antennas…

A: Ideal antenna has maximum radiation in all the directions. This is called isotropic radiator which…

Q: Required information Problem 05.001 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS The equivalent…

A: The given problem is from operational amplifier. The detailed solution is given in the next step

Q: The following results were obtained from measurements taken between the two terminals of a resistive…

Q: Determine the magnetic field at (0, 0, 5m) due to 15 A current flowing in a circular loop of radius…

A: Given- Current I = 15 A, A circular loop of radius 3 m, To Find- The magnetic field at (0, 0, 5m)…

Q: The output expression for the circuit given in Figure below is V1 10 k V2 WW 10 ΚΩ 10 k w 10 ΚΩ O…

A: Given opamp circuit is as follows.

Q: Voltage Across Resistor - using node Analysis, determine the Voltage Vo in [V] for the Circuit Shown…

A: To analyze the network circuit and find the voltage or current through any component Kirchoff's law…

Q: 95.6 cm and a radius of 1.90 cm. It consists of 1230 turns and carries a current of 3.58 A. how…

A: Given, l = 95.6 cm r = 1.90 cm N = 1230 T i = 3.58 A

Q: 24 V + www 80 www 30 20 ww 12.02 wwww 30

A: It is asked to find equivalent resistance of given circuit

Q: Write the UNSIMPLIFIED Boolean equation for output X of the following logic diagram, in terms of…

A: The given problem is from logic circuit. The detailed solution is given in the next step

Q: 4. Find i(t) on the following circuit for t 0. 1=0 6A Μ 4 Ω όλα (0) από πολλά άλλα προ i 2 Ω 3Η Ο

A: We need to find out the inductor current for given circuit .

Q: Identify the following: 1. This refers to the regions of magnetic alignment. 2. This phenomenon is…

A: it is asked to identify the definitions given

Q: The generator in Fig. 1 delivers 1 pu active power at 0.85 pf lagging to the infinite bus. 10.25…

A: Given P= 1 pu pf =0.85 lagging Xd' =0.15 infinite bus voltage , V=1 pu

Q: Consider the given circuit, where is = 3e mA. The voltage vo(t) is equal to 1.6 *et microV. What is…

A: We need to find out the value of unknown inductance for given circuit .

Q: Problem 04.036 - Thevenin equivalence with independent voltage sources Solve for the current i in…

Q: 5. Transmission of a radar screen's data requires transmission of data from 500000 pixels. Each…

Q: a-Find the mathematical expressions for the transient behavior of iz and vi for the circuit shown…

Q: A MOS device with an aluminum gate is fabricated on a p-type silicon substrate. The oxide thickness…

A: A MOS device with an aluminium gate is fabricated on a p-type siliconsubstratetox=22nm=220…

Q: Example 1: A 3-phase, 5kVA, 208V (line-to-line) 4-pole 60Hz (star-connected) synchronous machine has…

Q: 8. For this circuit, find the current I₁. A) 5.87 + j0.88 A B) 6.35 + j1.41 A C) -48 + j24 A D) 2.27…

Q: The single transistor in the circuit behaves as a +Vcc HII OUT

A: It is asked to state the behavior of transistor

Question

For the circuit below with R₁ = 10Ω, R₂ = 12Ω, X₁ =9, A = 44, B = -16 degrees, calculate the reactive power supplied by the source to the circuit in VARS.

For the circuit below with R₁ = 10N, R₂ = 12N, X₁ =9, A = 44, B = -16
degrees, calculate the reactive power supplied by the source to the circuit
in VARS. Please give the answer below with no
R₁
www
A <B
+1
jX₁
1
oooooo
R₂

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In an R-L parallel circuit, ET=240 volts, R=560, and XL=330. Find apparent power.
Find the branch currents, main branch current, impedance of the circuit, power coefficient of the circuit, apparent, active and reactive powers in the circuit below. I need step by step solution.
Write an expression for the output voltage vo(t) ofthe circuit shown if R1 = 1 k , R2 =2 k , R3 =47 k , v2(t)=(0.01 sin 3770t) V, andv1(t)=(0.04 sin 10000t)V. Write an expression forthe voltage appearing at the summing junction (v−).
Draw the below-given circuit. Change the value of components and add RL as a variable resistor. Use an ammeter to measure the current for various values of RL. Verify the Maximum Power Transfer theorem using the circuit below. Vth = 25 Volts and Rth = 140 Ohms.
Determine the Thévenin and Norton equivalents of the circuit. Ans: -7.857 V, -3.235 mA, 2.429 k ohms.
Prove that the phasor sum of the series components is equal to the source voltage. Attach your neat and complete solution for this. Thanks! ASAP.
Consider the circuit diagram below. Compute a single equivalent impedance for this circuit for a source frequency of ? =40 Hz. Express your final answer as a phasor with polar coordinates. You must show your all your work for the complex math. Include a diagram of the equivalent circuit as part of your solution.
In any circuit if we have AC and DC sources, then circuit must be analyzed by superposition Select one: True False
Determine the Norton equivalent for the circuit shown in the figureAnswer: RTH = 2 Ohms, icoc = -7.5A
Given: Load Voltage v(t) in volt = 240*sqrt(2)*sin(ωt+45 deg); Load Current i(t) in ampere = 10*sqrt(2)*sin(ωt-45 deg); Load active power in W = P; Load reactive power in Var = Q, ( Base your formal justification on the standard definition of active and reactive power. For your validation create and run a simple SimPowerSystems model ) Which one is the correct statement? To four significant figures: a. P =0 and Q = 2400 b. P=1697 and Q= -1697 c. P= 1697 and Q = 1697 d. P=2400 and Q=0
C. Solve the complex power delivered by each source and show that that total is equal to the complex power absorbed by all passive elements (R, L and C) in the circuit.
Differential equation is given as- Vo(t) = Vdd(1- (R/(R+Ron))*e^(-t/RC)) a) Assume Ron=280 ohm. When the load capacitor is C = 0.5nF, the output must reach 90% of its final value by t = 25uS. Find a value of R that will satisfy this requirement while at the same time keeping the static power below 1 mW. For your chosen resistance, calculate how long it will take to reach the 90% level.