Can you solve 12&13 please? Thank you! 12)For the circuit in Figure 5, determine the Thevenin Voltage seen by the load, RL. In thiscircuit, V, = 20v, R1 = 1k2, R2 = 1.5k2, and a = 0.001.+ VxR,R2V. OR,Figure 5a) VThb) VThc) VTh= OV= 10V= 7.5Vd) Vm = 20VThe) None of the above13)For the circuit in Figure 5, determine the Thevenin Resistance seen by the load, RL.

Answered: Image /qna-images/answer/ae449173-cdf9-4902-96db-c04165a55f93.jpg

For the circuit in Figure 5, determine the Thevenin Voltage seen by the load, RL. In this circuit, V3 = 20V, R1 = 1k2, R2= 1.5kN, and a = 0.001. 12) %3D %3D +. Vx R, R2 V. O a Vx Figure 5 a) Vm = 0V b) Vyh :10V c) Vm = 7.5V = 20V e) None of the above 13) For the circuit in Figure 5, determine the Thevenin Resistance seen by the load, RL.

For the circuit in Figure 5, determine the Thevenin Voltage seen by the load, RL. In this circuit, V3 = 20V, R1 = 1k2, R2= 1.5kN, and a = 0.001. 12) %3D %3D +. Vx R, R2 V. O a Vx Figure 5 a) Vm = 0V b) Vyh :10V c) Vm = 7.5V = 20V e) None of the above 13) For the circuit in Figure 5, determine the Thevenin Resistance seen by the load, RL.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 10PP: In an R-L parallel circuit, ET=240 volts, R=560, and XL=330. Find apparent power.

See similar textbooks

Similar questions

In the circuit below, the voltage sourse Vin = 12(V), and node D is grounded. Given R1 = 12 (Ω), R2 = 16 (Ω), R3 = 16 (Ω), and R4 = 16 (Ω). Find the voltage dropped cross R2, VA-VB, in volts.
For the circuit in the figure, find the ones requested in the questions by using the following values? VDD= 30 V, IDSS=8 mA, VP=-6V, R1=110 MΩ, R2=18 MΩ RD=1.9 kΩ, RS=3,68 kΩ VD=VS=VDS=
In the circuit given above VS = 17,3V, R1 = 11202, R2 = 11k1,If RL = 17.4kN and Vzener-5.6, how many mW will P(zener) be?
Answer the following questions related to a series/parallel combinational circuit configured as follows: R1 is in series with the source and also in series with the parallel combination of R2 and R3. The circuit’s voltage is +24VDC, R1= 4.5kΩ, R2=30kΩ, and R3=10kΩ. What is the Thevenin’s resistance (RTH) for the circuit described above if a load resistance of 20kΩ is placed in parallel with R2 and R3?
Topic: Direct Current Circuit which contains Open and Short Circuit, Series and Parallel Circuit, Current Divider Principle, Voltage Divider Prinicple, and Delta-Wyne Connection. Determine the value of VT and I. Note: DRAW THE DIAGRAM
Question: In the circuit to the right, R1 = R2,W/L = 3, Vtn = 0.6 V, and Kn = 200 A/V2. Determine the values of R1 and R2 such that VD = 1 V and Vs = -1 V.
Hey please reply as soon as posible Using only source transformation and without eliminating ix, reduce the circuit in Figure to a single voltage source and a single resistor, then obtain ix using Ohm's law. A) What is the value of the source voltage in V and what is the value of the resistor in Ω? B) What is the value of ix in Amps?
Since VDD = +15 V, VTH = +2 V and K = 100mA/V^2 in the circuit below, what is the ID current? (In circuit resistors The specified R value is in ohms) I want a quick solution, the method doesn't matter, the result matters
In the circuit given in the figure | VBE | = 0.7V, R1 = 34.65Kohm, R2 = 118.04Kohm, RC = 1.32Kohm, RE = 3.97Kohm, VCC = -12.00V, Beta = 287.00, calculate IC current with full analysis.
For calculating the Thevenin's Equivalent Resistance(RIh) at load terminals, remove the load resistance and if a voltage soure by a short circuit and a current source is replaced by an open circuit source is present replaced by an open circuit A_ True B_False
Given that Short circuit current - 5.52 A Open circuit voltage - 45.1 V Current at MPP - 5.19 A Voltage at MPP - 36.6 V Power at MPP - 190 W Number of PV cells and area of each cell - 72 cells (125mm × 125mm) Efficiency of PV module and the area of module - 14.9% efficiency (1581mm × 809mm × 35mm) Twelve (12) modules are configured into 4 strings of 3 modules in series. Two strings areput in parallel and then connected in series with another set of two strings in parallel. Determine the power at MPP under standard conditions.
4. A load rated at 115V, 60Hz, 10A and 1150W. A coil is to be wound with a ratio of XL to R of 5, such that when connected in series with the load on a 230V 60Hz line, the load may operate normally . Solve for R.