For the circuit shown blow, Use the Thévenin method of circuit analysis to Compute.The Rih is equal to?*1 point25 010022 020 0If the RI. value is equal to Rih the power that can be delivered by RL,equal to?*2 pointsBODW100ow900w30 0a360 V150 Ωξthe Vih is equal to?1 point320V250V300V270V

Answered: Image /qna-images/answer/58dbf2a1-7579-4d05-9782-f02c5536bb8f.jpg

For the circuit shown blow, Use the Thévenin method of circuit analysis to Compute. The Rih is equal to? 1 point 25 0 100 22 0 20 0 If the RL. value is equal to Rih the power that can be delivered by RL.equal to? 2 points BOOW 100ow 30 0 a 360 V 150 0E RL the Vih is equal to? 1 pont 320V 250V 300V 270V

For the circuit shown blow, Use the Thévenin method of circuit analysis to Compute. The Rih is equal to? 1 point 25 0 100 22 0 20 0 If the RL. value is equal to Rih the power that can be delivered by RL.equal to? 2 points BOOW 100ow 30 0 a 360 V 150 0E RL the Vih is equal to? 1 pont 320V 250V 300V 270V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I can't read these. Apply voltage divider rule:VL=RLRS+RLViminso,Vimin=RS+RLRLVLVimin=91Ω+220Ω220Ω×8 voltVimin=311220×8 VoltVi(min)=11.31 Volt From the circuit:VZ=VL=VA=8 Vso,IL=VLRL=8220AmpIL=36.364 mAandIZM=PzmaxVZ=4008mAIZM=50 mAApply KCL at node-AIRmax=IZM+ILIRmax=50 mA+36.364 mAIR(max)=86.364 mA Apply KVL in loop:-Vimax+RsIRmax+VZ=0Vimax=RsIRmax+VZput values:Vimax=91Ω×86.364mA+8VVimax=7.859 V+8 VVi(max)=15.859 V Hence range of Vi:11.31 V⩽V⩽15.859 VAnswer Pease if you could write it down on paper/digital paper or using LibreOffice or MS Office Word with Equation Operators.
The circuit in Figure 3 uses the T network to match the impedances of the load and the network in such a way that power transfer is maximum. The source operates at 60 Hz, has a series impedance of 50+5j Ω. what should be the impedance of the load for maximum power transfer if ?? = 0.385 ?, ? = 25.4 ?? and ?? = 0.566 ?? step by step detail
Show that the power, PL delivered to the load, RL can be expressed as: - PL= (RL) (Vth/(Rth+RL))^2 Show your analysis (ii) Show that the maximum power transfer takes place when the load resistance, RL = RTh, with the load voltage, VL = VTh/2. Show your analysis below.
Using Nodal analysis Measured Value = Vo=3.39v, V1=1.59V, v2=1.05v, v3=2.63v, v4=0.91v, v5=1.62v, v6=0.88v find the computed value of voltages v1, v2, v3, v4, v5, and v6. Ro=220 R1=330 R2=220 R3=330 R4=470 R5=470 R6=560
Dtermine i using source transformation. Show circuit transformation and step by step solution please thank you.
Given V1=60V, V2=20V, R1 = 23ohm, R2 = 34ohm, R3 = 35ohm, R4 = 42ohm, Find the value of the i at R = 200 ohm, using Norton's Theorem
Subject: CircuitsGivenRt = 37.9529 ohm..Rcd = 3.6 ohm.Rab=2.3529ohmIt=1.58APt=94.85WV2=3.16VV4=6.32VVab=3.7175vVcd=5.688VI10=0.372AI5=0.7435AI8=0.465AI9=0.632AI6=0.348AP2=4.9928WP4=9.9856WPab=5.88WP14=34.95WPcd=8.99WP12=29.96W
As shown in the Figure , an external load resistor, R, is connected across the terminal a-b of the DC circuit. Based on Norton’s Theorem, calculate and analyse the circuit shown in the figure ( given V1=60V, V2=20V, R1 = 22ohm, R2 = 34ohm, R3 = 35ohm, R4 = 42ohm,) to determine the current, i, when R = 200 Ω
Redraw the Norton Equivalent circuit for Thevenin Equivalent Circuit using a previous problem that was solved and calculate the load current (IL ) dropped across the load resistor (RL)? NOTE (backround information): for this example and the circuit you see below we were asked to perform Thevenins equivalent circuit. We were asked to find... Rth, Eth, and IL the anwers I got were Rth= 1 kΩ Eth= 3 V IL= 0.273 mA
Write an expression for the output voltage vo(t) ofthe circuit shown if R1 = 1 k , R2 =2 k , R3 =47 k , v2(t)=(0.01 sin 3770t) V, andv1(t)=(0.04 sin 10000t)V. Write an expression forthe voltage appearing at the summing junction (v−).
For the circuit below with R1 = 10Ω, R2 = 12Ω, X1 =9, A = 44, B = -16 degrees, calculate the reactive power supplied by the source to the circuit in VARS.
For the circuit shown below if the complex power of branch 2 is S2=1490 VA Find 1.P,Q, S, PF, for each branch 2. PT,QT,ST,PFT 3.Draw the complete power triangle 4. IT. I1, I2