For the circuit shown in (Eigure 1) both meters are idealized, the battery has no appreciable internal resistance, and the ammeter reads 1.95 A Figure < 1 of 1 What does the voltmeter read? Express your answer in volts. 15. ΑΣΦΑ Submit Previous Answers Request Answer Part B * Incorrect; Try Again; 4 attempts remaining ? What is the emf & of the battery? V

For the circuit shown in (Eigure 1) both meters are idealized, the battery has no appreciable internal resistance, and the ammeter reads 1.95 A Figure < 1 of 1 What does the voltmeter read? Express your answer in volts. 15. ΑΣΦΑ Submit Previous Answers Request Answer Part B * Incorrect; Try Again; 4 attempts remaining ? What is the emf & of the battery? V

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter20: Electric Current, Resistance, And Ohm's Law

Section: Chapter Questions

Problem 14CQ: The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance...

See similar textbooks

Similar questions

The circuit shows R= 1 ohm, Emf1= 12.2 V and Emf 2= 7.1 V. What is the power delivered to the 10R resistor in W? Note: 1.0857 is the correct answer. Show.
For the circuit shown in the figure, I = 0.50 A and R = 12 Ω. What is the value of the emf ε? I believe it has to do with Kirchhoff's Rules but am not sure how to apply it.
Given the following circuit, find theequivalent resistance and the voltageacross R2. Let V = 16 V, R1 = 4 Ω, R2 =2 Ω, R3 = 6 Ω, R4 = 3 Ω, and R5 = 5 Ω .
Imagine that we had a RC circuit with a 19.2 kilo-ohm resistor connected in parallel with a 16 kilo-ohm resistor and they were connected to two capacitors (404.2 uF, 350.1 uF) that are in series. What is the time constant of this circuit?
1 Supposing the voltmeter used has a resistance of 20,000 ohms and it reads 5 volts while the ammeter reads 0.02 ampere, a) What is the unknown resistance as computed? B) What is the actual value of the unknown resistance? 2. In the simplified slide-wire Wheatstone Bridge Circuit shown in the figure, the sliding contact C was at the 40cm mark when G reads zero and Rs = 10ohms, a) What is the unknown resistance Rx ? b) If Rs = 5ohms and the same unknown resistance in a) is measured, on what mark will the sliding contact C be to make the galvanometer reading zero? bartleby limits to 3 answers only but can I have explanation to those unanswered? or hint how to solve
How do you find the value of a resistance R1, in a circuit when the equivalent resistance is 40 ohms, given that: R2 = 12 ohm in series with R3 = 40 ohms whom combined are in parallel with R4 = 20 ohms, all in parallel to R1. And to find the current in each resistor, do I just apply the equation, I = V/R, given that the circuit runs on an 28 volt batt.
The circuit shown in the diagram consists of a 10-volt battery, a 47-ohm resistor, and 0.375-farad capacitor, connected as shown. The time constant for this circuit is calculated as follows. τ= RC= (47 Ω )(0.375 F) = 17.6 s. Suppose the switch had been in Position 1 for a long time and is just being moved to Position 2. Let t = 0 at the instant the switch is placed in Position 2. What will the voltage be across the capacitor when the time t = 17.6 s?
What must be the emf in the circuit so that the current flowing through the 7 ohm resistor 1.80 A ? Each emf source has negligible internal resistance
If R1= 1Ω, R2=2Ω and Ru=3Ω, (a) to what value the Rvar should be adjusted so as to achieve balance condition? (b)If V0 = 6 V, Ra = 0.1 Ω(resistance in the meter), and Ru were then to deviate by a small amount to Ru = 3.01 Ω, what would be the reading on the ammeter?
3.3 calculate the: 3.3.1 effective resistance of the parallel combination of resistors. 3.3.2 total resistance of the circuit. 3.3.3 reading on ammeter A2 3.3.4 reading on ammeter V1
What is the total power (W) dissipated in the two resistors in the circuit shown if R1=10ohms, R2=19ohms and V=14 volts?
What is the time constant of this circuit? a)10 microseconds, b) 1 microsecond, c) 1 millisecond or d) 100 microseconds?