For the circuit, take VTN=0.8V, the conduction parameter Kn-1 mA/V2 and X-0. Calculate the Gate-Source voltage VGS and drain- source voltage VDS. Choose one of the answer choices that is closest to what you have found. +6V A B VGS-1.27V and VDS-10.32V VGS-2.3V and VDS-6.8V C) VGS-1.12V and VDS-8.44V Cc HE www R₁ = 85 k R₂ = 20 k -6V RD=8k 010 Rs = 1 k

For the circuit, take VTN=0.8V, the conduction parameter Kn-1 mA/V2 and X-0. Calculate the Gate-Source voltage VGS and drain- source voltage VDS. Choose one of the answer choices that is closest to what you have found. +6V A B VGS-1.27V and VDS-10.32V VGS-2.3V and VDS-6.8V C) VGS-1.12V and VDS-8.44V Cc HE www R₁ = 85 k R₂ = 20 k -6V RD=8k 010 Rs = 1 k

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An N-channel MOSFET with N+-poly gate is fabricated on a 15 n. cm P-type Si wafer (a) Determine the flat-band voltage Vfb. (b) What is the threshold voltage, Vt? (c) A circuit designer requested N-MOSFET with Vt = 0.5 V from a device engineer. It was not allowed to change the gate oxide thickness. If you are the device engineer, what can you do? Give specific answer.; including what type of equipment to use.
For the common gate configuration, determine: IDQ and VGSQ through the graphical analysis. Also, obtain the values of ??, ??and ???. It has the following data of the different elements of the circuit such as: RD = 2.2 kΩ, RS = 2.2 kΩ, VDD = 16 V and VSS = - 4 V. The manufacturer's sheet indicates that it has IDSS = 6 mA and VP = - 6 V.
For the transistor , IS = 4 × 10−16 μA,βF = 75, and βR = 4. (a) Label the collector, base,and emitter terminals of the transistor. (b) What isthe transistor type? (c) Label the emitter-base andcollector-base voltages, and label the normal direction for IE , IC, and IB. (d) Write the simplified formof the transport model equations that apply to thisparticular circuit configuration. Write an expressionfor IE /IB. Write an expression for IE /IC. (e) Findthe values of IE , IC, IB, VC B, and VE B.
Advanced small geometry transistors have valuesof VBE that are larger than 0.7 V. (a) Redesign theECL gate as shown if VBE of the transistors is 0.85V. What are the newvalues of VOH, VOL, and VREF?(b) Repeat for VBE = 0.95 V.
For an n-channel depletion-mode MOSFET, in the saturation region ID = 8mA when VGS = 0, and the dynamic (incremental) output resistance r0 is infinite. The threshold voltage (or pinch-off voltage) is VTR = VP = –2.5V. For VGS = 0, find the smallest value of VDS at which the MOSFET is in saturation. For VDS equal to this value, find ID when (i) VGS = –1V, (ii) VGS = –2V, (iii) VGS = –3V, (iv) VGS = –4V.
For the transistor , IS = 6×10−16 μA,αF = 0.985, and αR = 0.25. (a) What type oftransistor is in this circuit? (b) Label the collector, base, and emitter terminals of the transistor.(c) Label the emitter-base and collector-base voltages, and label the normal direction for IE , IC, andIB. (d) Write the simplified form of the transportmodel equations that apply to this particular circuitconfiguration. Write an expression for IE /IC. Writean expression for IE /IB. (e) Find the values of IE ,IC, IB, βF , βR, VE B, and VC B.
The drain of an MOSFET is shorted to the gate.Threshold voltage=1 v .If the drain curent is 1mA for Vgs=2v ,what will be the drain curent value if Vgs is increased by 1v
I-V Characteristics of NMOS device: The following graph shows the I-V characteristics of an NMOS device. Answer the following questions: [10] A. Find out the three regions of operation (linear, saturation, and cut-off) of the following graph and give a brief explanation of them by using the different operating modes (accumulation, depletion, and inversion). B. In the graph, the saturation voltages from drain-to-source increase with increasing gate-to-source voltages. Give a brief explanation of why: Vds(sat,A)<Vds(sat,B)<Vds(sat,C)
Identify the source, drain, gate, and bulk terminals for the transistors in the two circuits in. Assume VDD = 10 V.
When calculating the drain current in an NMOS transistor, what formula is used given that Vds<Vgs-Vt
Implement circuit for following scenario using NAND gate only, draw circuit using multiplexer In a certain chemical – processing plant, a liquid chemical is used in a Manufacturing process. The chemical is stored in three different tanks. A level sensor in each tank produces HIGH voltage when the level of chemical in the tank drops below a specified point. Design a circuit that monitors the chemical level and indicate when the level in any two of the tanks drops below the specified point. Draw the circuit using NAND gate only and implement using Multiplexer
For the MOSFET circuit given below, a) The depletion NMOS transistor has IDSS = 4mA and VP = -4V. Given that VDD = +10V and RD = 1kΩ Find the region of operation for the MOSFET and calculate the parameters of VGS, ID and VDS. b) Replace the short circuit that is connected between the gate and the drain with a 1MΩ resistor. In addition, place another 1MΩ resistor between the gate and the reference. Given that K = 0.25mA/V2, Vt =2V, RD = 500Ω and VDD = +12V. Find the region of operation for the MOSFET and calculate the parameters of VGS, ID and VDS.