For the circular thin plate with a square hole as shown in the image below, its radius R = 0.42 m and the side of the square /= 0.15 m, and the material has a mass per unit area of 15 kg/m2. If at the instant shown, it is subjected to a force P= 47 N, and has a counterclockwise angular velocity of w = 2.1 rad/s, determine the angular acceleration (in rad/s?) of this plate. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². R 4 3 Your Answer: Answer

For the circular thin plate with a square hole as shown in the image below, its radius R = 0.42 m and the side of the square /= 0.15 m, and the material has a mass per unit area of 15 kg/m2. If at the instant shown, it is subjected to a force P= 47 N, and has a counterclockwise angular velocity of w = 2.1 rad/s, determine the angular acceleration (in rad/s?) of this plate. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². R 4 3 Your Answer: Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q4:-A rotating shaft carries four masses 176.6 N, 137.3 N, 157 N and 117 N at radii 5 cm, 6 cm, 7 cm and 6 cm respectively. The second, third and fourth masses revolve in planes 8 cm, 16 cm and 28 cm respectively measured from the plane of the first mass (at the left end). They are angularly located at 60o, 135oand 270orespectively measured clockwise from the first mass (at the positive x-axis). The shaft is dynamically balanced by two masses both located at 5 cm radii and revolving in planes midway between those of 1st and 2nd masses and midway between those of 3rd and 4th masses. Determine the magnitude of the masses and their respective angular positions.
In the figure shown, the hydraulic cylinder moves upwards with a constant speed of Va=0.2 m/s, transferring vertical movement to corner A of the container. If bearing b never slips and has a diameter of 8 cm, determine the angular velocity of the imaginary line drawn from its axis of rotation to any point on its periphery. Determine the angular velocity of side CD at this moment.
The paint stirrer shown in the figure is made from a rod of length 7b and mass rho per unit length. Before immersion in the paint, the stirrer is rotating freely at a constant high angular velocity w about its z-axis. Determine the bending moment M in the rod at the base O of the chuck.
The mass of flywheel of an engine is 8 tonnes and the radius of gyration is 1.8 metres. It is found from the turning moment diagram that the fluctuation of energy is 100 kN-m. If the mean speed of the engine is 150 r.p.m., find the maximum and minimum speeds.
The frame of a gyroscope in fig. is supported at O so that it can turn freely in alldirections. The wheel is a uniform disc of 10 cm diameter weighing 2 kg with its centre20 cm from O. The frame alone weighs 1 kg with centre of gravity G1, 12 cm from O.If the wheel spins as shown at 10,000 r.p.m. with its axle in the horizontal plane, findthe time required for the axle to make one revolution about O. Mention the direction ofthis rotation. Find also the vertical and horizontal forces by the support on the frame.
At the top A of the vehicle moving along line AC in the figureIts speed is 30 m / sec and its weight is 9 kN.Tool radius of curvature 40The reaction force to the tires when reaching point B, which is m,and so that the tires do not separate from the asphalt when it reaches point CWhat should be the radius of curvature of point C? (hA = 6 m andhC = 9 m)
The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.
A shaft with 3 meters span between two bearings carries two masses of 10 kg and 20 kg acting at the extremities of the arms 0.45 m and 0.6 m long respectively. The planes in which these masses rotate are 1.2 m and 2.4 m respectively from the left end bearing supporting the shaft. The angle between the arms is 60°. The speed of rotation of the shaft is 200 r.p.m. If the masses are balanced by two counter-masses rotating with the shaft acting at radii of 0.3 m and placed at 0.3 m from each bearing centers, estimate the magnitude of the two balance masses and their orientation with respect to the X-axis, i.e. mass of 10 kg ‎‏Note: It must be solved using the graphic method, not the equations method.
A shaft with 3 meters span between two bearings carries two masses of 10 kg and 20 kg acting at the extremities of the arms 0.45 m and 0.6 m long respectively. The planes in which these masses rotate are 1.2 m and 2.4 m respectively from the left end bearing supporting the shaft. The angle between the arms is 60°. The speed of rotation of the shaft is 200 r.p.m. If the masses are balanced by two counter-masses rotating with the shaft acting at radii of 0.3 m and placed at 0.3 m from each bearing centers, estimate the magnitude of the two balance masses and their orientation with respect to the X-axis, i.e. mass of 10 kg.
A rotating shaft carries four unbalanced masses 18 kg, 14 kg, 16 kg and 12 kg at radii 50 mm, 60 mm, 70 mm and 60 mm respectively. The 2nd, 3rd and 4th masses revolve in planes 80 mm, 160 mm and 280 mm respectively measured from the plane of the first mass and are angularly located at 60°, 135° and 270° respectively measured clockwise from the first mass.The shaft is dynamically balanced by two masses, both located at 50 mm radii and revolving in planes mid-way between those of 1st and 2nd masses and midway between those of 3rd and 4th masses. Determine, balancing mass by drawing couple polygon and their respective angular position graphically.
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
Blocks A and B shown in the figure have masses of 5 kg and 10 kg respectively.If the pulley is treated as a 3 kg solid disk with a 15 cm radius, determine the acceleration of the block A. Disregard the rope mass and any slip on the pulley.Consider that the moment of inertia of the pulley is given by Ip = (1/2)mr² in which m is the mass of the pulley and r is of radius the pulley.