For the figure shown, calculate the net area of the 10 x 200 mm plate. The plate is connected at its end with two lines of 20 mm bolts. Using LRFD, determine the load P that the plates can carry against tensile yielding in the gross section and the tensile rupture in the net section. Use A-36 steel.

For the figure shown, calculate the net area of the 10 x 200 mm plate. The plate is connected at its end with two lines of 20 mm bolts. Using LRFD, determine the load P that the plates can carry against tensile yielding in the gross section and the tensile rupture in the net section. Use A-36 steel.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.6.5P

See similar textbooks

Similar questions

Determine the Net Area for the following Plate Section consider all possible Cases. The Plate thickness is 1-in. and the bolts' diameter is 7/8-in. s = 6.0 " g = 2.0 "
an angle bar 100x100x11 mm tension member is connected with 20-mm-dia bolts as shown in the fig. both legs of the angles are connected. use fy=248 MPa and Fu=400 MPa. 1. determine the nominal strength for tensile yielding in the gross section. a. 515.59 kN b. 429.67 kN c. 545.60 kN d. 390.10 kN 2. determine the effective net area of member a. 1573 mm^2 b. 1632 mm^2 c. 1605 mm^2 d. 1815 mm^2 3. determine the nominal strength for tensile rupture in the net area. a. 642 kN b. 730 kN c. 554 kN d. 650 kN
5. a bolted lap joint shown in the figure below. The bolts are 20m in diameter in 23 mm holes. The plates are 12m thick X350 Allowable stress of Plates: Tenaion in gross area0.60Fy Tension in net area0.50 Fu Shear on Net Area 0.30Fu Yield Strength of plate, Fy 248 Npa Ultinate tensile strength of Plate. Fu400 Mpa x, Find the safe load P based on a- Gross area yielding b. net area rapture c. block shear 2 of 3
A 1 ⁄2 × 5-inch plate of A588 steel is used as a tension member. It is connected to a gusset plate with four 5 ⁄8-inch-diameter bolts as shown in Figure 1. Assume that the effective net area Ae equals the actual net area An. (a) Calculate the design strength for LRFD? (b) Calculate the allowable strength for ASD?
The tension member shown in Figure is an L6 × 3 ½× 5/16. The bolts are ¾ inch ameter. If A36 steel is used, is the member adequate for a total load of 100 kips?
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
The unbraced column length of Round HSS 18 x0.5 in A500 Grade C (Fy = 50 ksi) is 30 ft.Determine the design compressive strength of the column using the equations in Chapter E inPart 16 of the AISC Manual. Confirm your answer using the AISC Manual Table 4-5 (pages 4-84,New AISCM) and (pages 4-84, New AISCM). The column has pin supports at both ends ( i.e Kx= Ky = 1.0) columns. Lx = Ly = 30 ft
Three steel bolts are to be used to attach thesteel plate shown to a wooden beam. Theplate will support a 110kN and the ultimateshearing stress for the steel used is 360MPaand that a factor of safety of 3.35 is desired,determine the increase in the bolt diameterrequired if an additional 100kN load is addedto the existing 110kN.
3. A single angle tension member L89x89x9.5 with an area of 1,800mm2 connected to a gusset plate with 22 mm diameter bolts as shown in the figure. A36 steel is used with Fy=248 MPa and Fu= 400 MPa. The service loads are 150 KN dead load and 65 KN live load. Investigate the adequacy of the member. Diameter of hole is 3 mm bigger than bolt diameter and use net area equal to 85% of the computed net area. Neglect block shear. a. Check using ASD Load Combination b. Check using LRFD load combination
If the allowable bearing stress in the bolt is 18.855 ksi. what is the minimumrequired diameter of the bolt at B? b= .75” h= 7.874” Distances are in feet.
An unsymmetrical flexural member consists ofa 3 x 30 in. top flange, a 3 x 20 in. bottom flange, and a 60 * 2 in web A. Determine the distance from the top ofthe shape to the horizontal plastic neutral axis. B. If A572 Grade 50 steel is used, what is the plastic moment Mp for the horizontal plastic neutral axis?
The clevis shown below, find the minimum bolt diameter and the minimum thickness of each yoke thatwill support a load P = 56 kips without exceeding a shearing stress of 54 ksi and bearing stress of 60 ksi. MAKE ATLEAST 4 DECIMAL POINTS.