1. Free body: Entire frameo In total, there areΟΟΟΣ F, = 0 : Ay•ΣΜΑ = 0 : ExΣ Fx = 0 : AxXΟ2. Free body: member CDE:Σ Mc = 0 : D.=3. Free body: member ABD:o From above, Dx =o Σ=• ΣΕ = 0 : B =: BxΟ==ΣΜΒMg = 0 : D,:==Σ F, = 0 : B, =yforces/reactions acting on the frame;lb;lb;lb;lb pointing to thelb;lb;pointing thelb;♦→ Forthe frame and loading shown, determine the components of all forces acting on member ABD. Given that P₁ = 420lb,P2 = 300lb.6 in.-9 in.9 in.9 in.-P₁DE12 in.12 in.

Name: 1. Free body: Entire frameo In total, there areΟΟΟΣ F, = 0 : Ay•ΣΜΑ =
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 1. Free body: Entire frameo In total, there areΟΟΟΣ F, = 0 : Ay•ΣΜΑ = 0 : ExΣ Fx = 0 : AxXΟ2. Free body: member CDE:Σ Mc = 0 : D.=3. Free body: member ABD:o From above, Dx =o Σ=• ΣΕ = 0 : B =: BxΟ==ΣΜΒMg = 0 : D,:==Σ F, = 0 : B, =yforces/reactions a

Answered: Image /qna-images/answer/5b97e43f-7f87-43a9-97a6-f01d29fbc5b0.jpg

Answered: For the frame and loading shown,…

Engineering

Mechanical Engineering

For the frame and loading shown, determine the components of all forces acting on member ABD. Given that P₁ = 420lb, P2 = 300lb. ● A 6 in. B -9 in.-9 in.- 9 in. C 12 in. 12 in.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.64P: The two main cables of the Akashi Kaikyo suspension bridge in Japan have a span L=1990m and a sag...

See similar textbooks

Similar questions

The hoist supports an engine of weight W in kg. Determine the force the load creates in member DB and in member FB, which contains the hydraulic cylinder H. Given: X=2 m ; L=3 m ; W= 123 kg.
The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly distributed load of w0 N/m along the horizontal. If the maximum allowable force in the cable is 4 MN, determine the largest permissible value of w0.
The triangular block below is subjected to the Loads P=1200 lb and 400 lb. If AB=8 in, and BC is 6in., resolve each load into components normal and tangential to AC.
Determine the bar forces of member BG. For the given loads: X= 15kN, Y= 45kN, Z= 60kN, B= 15
A triangular block shown is subjected to the loads S = 1000 lb and T = 2000 lbs. If AB = 8 in and BC = 6 in, resolve each load into components normal and tangential to AC.
Determine the weight of the heaviest cylinder which can be placed in the position shown without exceeding a stress of 50 MN/m2 in the cable BC. Neglect the weight of the bar AB. The cross – sectional area of cable BC is 100mm2.
Three cables are used to support a plate of weight W lb. Determine the tension that is needed in each cable to achieve the equilibrium position. Givens-> W: 13 LbΘ°: 13X: 713 mm Please only in Lb
The beam is supporting a distributed load of w=660 lb/ft. Determine the magnitudes of the resultant internal loadings acting on section b–b through the centroid C on the beam. Show all work and any FBDs that apply.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
The rigid bar ABC is suspended from three wires of the same material. The cross-sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P.
Suppose P = 2500 lb. From the frame below, determine the magnitude and direction of (1) Ax and Ay (2) Dx and Dy (3) the vertical and horizontal component of the force at C as it acts on member BCD
Consider one end of a timber roof truss that is supported on a masonry wall. The reaction at the masonry wall must be only vertical. Assuming that the maximum capacity of either the inclined or horizontal members is 10 kips, determine the maximum magnitudes F1 and F2 so that their resultant is vertical through the masonry wall.