For the given circuit, Vcc 19 volts, Rg = 900 KO, Rc = 8 K2, RE = 3 KN and B = 100. Assume Transistor is Silicon, VBE=0.7 volts. Vcc RC RB RE a. Compute for the base current Q-point, IBa (in Amperes) b. Compute for the collector current Q-point, Ica (in Amperes) [ c. Compute for the collector-to-emitter voltage, VCEQ (in Volts) d. Draw the Load Line, with details. Note: Upload your answers as PDF file in the Moodle Final Exam submission link. 1. Base current Q-point in amperes is

For the given circuit, Vcc 19 volts, Rg = 900 KO, Rc = 8 K2, RE = 3 KN and B = 100. Assume Transistor is Silicon, VBE=0.7 volts. Vcc RC RB RE a. Compute for the base current Q-point, IBa (in Amperes) b. Compute for the collector current Q-point, Ica (in Amperes) [ c. Compute for the collector-to-emitter voltage, VCEQ (in Volts) d. Draw the Load Line, with details. Note: Upload your answers as PDF file in the Moodle Final Exam submission link. 1. Base current Q-point in amperes is

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Derive the Avf, Rif, Rof, R’of for the circuit shown in figure 1. For each transistor theh-parameters, hie and hfe are equal.
For the NMOSFET in the circuit below, K = 2.00mA/V2, VTHN = 1.00V, l = 0.05V-1, and VIN = 3.50V. a. Solve for IDS and VOUT and verify any assumptions you made. b. Calculate the small signal gain of the circuit, vout / vin .
A base voltage of four volts is applied to an NPN bipolar junction transistor. A twenty kilo ohm resistor is linked to the base, while a hundred kilo ohm resistor is connected to the collector. The Collector is powered by a six volt supply voltage. Assume the transistor is in active mode, with a fifty common Emitter current gain(β).(i) Utilize the dc equivalent model of the transistor to draw the circuit design.(ii) Calculate the Collector current (IC) and the Base current (IB) .ii) Locate/determine the result (VCE).
IBQ, ICQ, VE, VCEQ, VCfor a transistor with VBE= 0.6 and β = 50. Draw and label the DC load-line. From b, if transferred to the center of the load-line, determine new values of R1 and R2 and draw the final circuit.
Instruction/s: Draw, Illustrate and label your schematic diagram before solving the problem. 1.) Given a Fixed-Biased transistor circuit with Beta DC is 200 , voltage at common collector is +22v ,base supply voltage is +11V, Base resistor is 47kOhms , collector resistor is 390 ohms ,Voltage at Base-emitter junction is 0.7v. Determine the Q-point of collector current and Voltage at collector-emitter junction. These is the example or guide that might help in answering the problem.
What is the voltage value Vgs for the n-channel MOSFET given in the figure? (VT=2V, K=0.4mA/V^2, VDD=5V, RD=RS=1K)
An enhancement-mode n-channel MOSFET has gate-source threshold voltage VTR = +2V and source-drain conductance parameter K = 1.0 mA/V2 (= the constant of proportionality between source-drain current and the square of the excess of gate-source voltage over the threshold voltage, when the MOSFET is in constant-current or saturation mode). Its source terminal is connected to ground. The gate terminal is connected direct to the drain terminal and also to one end of a 1 kΩ resistor. The other end of this resistor is connected to the +15V supply. (i) Show that, assuming it is conducting at all, the MOSFET is operating in constant-current (i.e., saturation) mode; (ii) calculate the current in the resistor and the voltage across it.
Consider a voltage-divider configuration of n-channel enhancement-type MOSFET where R1 = 12 MΩ, R2 = 7 MΩ, RD = 3 kΩ, RS = 1 kΩ. The MOSFET has a threshold voltage VGS(Th) = 3V, and one example point on the transfer characteristics curve is VGS(on) = 6V, ID(on) = 5 mA. Determine VGSQ, IDQ, Vs, VD, VDS assuming VDD = ( 80 ÷ 10 ) +20 V
(b) For an n-channel enhancement MOSFET with threshold voltage of 2.5V, determine the current at values of gate-source voltage(i) VGS= 4V and(ii) VGS= 6V [k=0.3mA/V2] (c) Determine the values of transconductance for an n-channel enhancement MOSFET having threshold voltage VT = 3V at the following operating points(i) 6V and(ii) 8V
Draw, Illustrate and label your schematic diagram before solving the problem. 1) Given a Fixed-Biased transistor circuit with Beta DC is 200 , voltage at common collector is +22v ,base supply voltage is +11V, Base resistor is 47kOhms , collector resistor is 390 ohms ,Voltage at Base-emitter junction is 0.7v. Determine the Q-point of collector current and Voltage at collector-emitter junction. These might be help as a guide to solve the problem.
Draw, Illustrate and label your schematic diagram before solving the problem. 3) Given an Emitter-Stabilize Biased transistor circuit with beta DC is 250,Base resistor is 150 ohms, collector resistor is 1.5k ohms ,emitter resistor is 500 ohms ,emitter voltage supply is -5v and Voltage at common collector is +28V,Voltage at Base-emitter junction is 0.7v,. Determine Base current, Collector current and Voltage at collector-emitter junction.
In the circuit shown, RL = 2 k , VCC =15 V, and −VEE = −15 V. (a) What is the maximumvalue of RE that can be used if vO is to reach−12.5 V? (b) What is the emitter current of Q1when vO = +12.5 V?