For the given loads F1=48 KN, F2=33 KN, F3=49 KN, F4=24 KN (Assume internal forces are in tension) F1 F2 F3 F4 F3 F2 F1 0.8 m 0.8 m 0.8 m 0.8 m 0.8 m 0.8 m D Bo E GV H\ 0.4 m C Magnitude of reaction at K is (KN) а. 284 b. 213 C. 142 d. 355 e. 426 Magnitude of reaction at A is (KN) intemal force in member IK (KN) is intemal force in member JH (KN) a. -564 b. -282 C. -376 d. -470 e. -188 intemal force in member IH (KN) a. -341.00037 b. -204.600222 C. -272.800296 d. -136.400148 e. -409.200444 intemal force in member GF (KN)

For the given loads F1=48 KN, F2=33 KN, F3=49 KN, F4=24 KN (Assume internal forces are in tension) F1 F2 F3 F4 F3 F2 F1 0.8 m 0.8 m 0.8 m 0.8 m 0.8 m 0.8 m D Bo E GV H\ 0.4 m C Magnitude of reaction at K is (KN) а. 284 b. 213 C. 142 d. 355 e. 426 Magnitude of reaction at A is (KN) intemal force in member IK (KN) is intemal force in member JH (KN) a. -564 b. -282 C. -376 d. -470 e. -188 intemal force in member IH (KN) a. -341.00037 b. -204.600222 C. -272.800296 d. -136.400148 e. -409.200444 intemal force in member GF (KN)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.55P: Solve Prob. 10.54 assuming that A and B are connected by a spring of stiffness k = 0.3 W/b and free...

See similar textbooks

Similar questions

review engineering statics Take d1 = 600 mm, d2 = 800 mm, θθ = 45° and F = 500 N (a) Show that member DB is a two-force member? Draw a qualitatively correct extended free-body diagram of DB. (b) Draw an extended FBD of member ABC. (c) Write the three equilibrium equations for member ABC (namely Fnet, x = 0, Fnet,y = 0, and Mnet/P,z = 0). Make clear the choice of your point P for the moment equation. (d) Find the forces acting on member ABC at A and B (give your answer in component form or as a direction and magnitude.) Show your work. These are my answers FBD=2F, RAX=353.5N RAy= 353.5N but am not sure if a correct any help
review engineering statics Take d1 = 600 mm, d2 = 800 mm, θθ = 45° and F = 500 N (a) Show that member DB is a two-force member? Draw a qualitatively correct extended free-body diagram of DB. (b) Draw an extended FBD of member ABC. (c) Write the three equilibrium equations for member ABC (namely Fnet, x = 0, Fnet,y = 0, and Mnet/P,z = 0). Make clear the choice of your point P for the moment equation. (d) Find the forces acting on member ABC at A and B (give your answer in component form or as a direction and magnitude.) Show your work.
For Fz= 200 lb and all other forces zerodetermine the factor of safety of member B-C halfway between B and C. Steel, Sy = 36ksi
Statics-Two Force Members 1. Determine the force P required to maintain equilibrium of the pulley system, and the reactions at the ceiling. 2. Assume W=1.25kN 3. Show and clearly label all Free Body Diagram to determine solution.
Solve Prob. 10.54 assuming that A and B are connected by a spring of stiffness k = 0.3 W/b and free length b.
To determine the reaction forces at supports on a horizontal beam by using the equations of equilibrium for a static application. As shown, beam ABC is supported by the roller at A and pin at C. The geometry of the beam is given by a=2.0a=2.0 ftft, b=7.0b=7.0 ftft, and c=12.0c=12.0 ftft. The applied forces are F1=1.50F1=1.50 kipkip and F2=2.00F2=2.00 kipkip. Force F1F1 is applied at an angle θ=60∘θ=60∘ with the horizontal. Neglect the weight of the beam.(Figure 1)
P1=215 N P2=325 N P3=150 N L1=3m L2=4m 1. Draw a "free body diagram". The diagram should be for members BE, BF, CF, and DF to help solve. 2. What is the force on members CF, BF, BE? Is each of these members having tension or compression?
Q 40/A homogeneous bar of length / and weight w lb rests horizontally as shown in Fig. 40 with its free endon a block of weight W. the block W is at rest on a plane inclined at the angle a with the horizontal. Determine the necessary coefficient of friction u between the block and the plane for equilibrium. Assume no friction between the bar and the block.
Determine the forces in members EF, GH and GI of the truss shown & designate whether the member is Tension or Compression. EF = 5 kips (T), GI = 10.4 kips (T), GH = 33 kips (T)EF = 5 kips (C), GI = 10.4 kips (C), GH = 33 kips (T)EF = 5 kips (C), GI = 10.4 kips (T), GH = 33 kips (C)EF = 5 kips (T), GI = 10.4 kips (C), GH = 33 kips (C)EF = 5 kips (C), GI = 10.4 kips (C), GH = 33 kips (C)EF = 5 kips (T), GI = 10.4 kips (T), GH = 33 kips (C)EF = 5 kips (C), GI = 10.4 kips (T), GH = 33 kips (T)EF = 5 kips (T), GI = 10.4 kips (C), GH = 33 kips (T)
The frame is used to carry high-voltage wires. If b=600mm, α=30° and W=981 N, find the internal force in member HJ? (Draw free body diagram)
What is Equilibrium of a Rigid Body? Give an example.
Application of Equilibrium Solve for the value of unknown variables Given : P1 = 6.85 KN P2 = 4.65 KN W1 = 6.15 KN/m Unknowns : RAy , RAx ,RBy , MA What is the value of internal shear 2.50m to the right of support A