For the given system below, the coefficient of static friction between surfaces are faB - 0.20, fBC - 0.10 and fp - 0.15. Block B impends to slide to the right. The resultant of friction and normal force exerted by C on B makes an angle 20 30' M O 20° up to the left with the normal force O 5.71° up to the right with the normal force O 35.71° up to the left with the vertical O 31.31° up to the left with the vertical.

For the given system below, the coefficient of static friction between surfaces are faB - 0.20, fBC - 0.10 and fp - 0.15. Block B impends to slide to the right. The resultant of friction and normal force exerted by C on B makes an angle 20 30' M O 20° up to the left with the normal force O 5.71° up to the right with the normal force O 35.71° up to the left with the vertical O 31.31° up to the left with the vertical.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.36P: The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find...

See similar textbooks

Similar questions

The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
A 1.1-kg disk A is placed on the inclined surface. The coefficient of static friction between the disk and the surface is 0.35. Is the disk in equilibrium if P=5.5N and =30?
The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the pressure in pounds per square inch (psi) and r represents the radial distance in inches. Determine the torque C required to operate the sander at constant speed if the kinetic coefficient of friction for the surface being sanded is 0.86.
A box slides from rest from point A down a plane inclined 30 degrees to the horizontal. After reaching the bottom of the plane, the box moves on the horizontal floor at a distance of 2 m before coming to rest. If the coefficient of friction between the box and plane and between the box and floor is 0.40, what is the distance of point A from the intersection of the plane and the floor?
A horizontal force is exerted on a 150 lb chair at rest. The coefficient of static friction between the chair and the floor is 0.55. Determine the maximum horizontal force that can be applied to the chair before it moves.