For the lossless TL shown in below with length 1, let Zg - 620, ZR = (open circuit load) and the supplied voltage is 100V. Use Zig-zag diagram to show the incident and reflected signals for 8T, then draw the time-spacing diagram for the sending end ES and IS and receiving end ER and IR

For the lossless TL shown in below with length 1, let Zg - 620, ZR = (open circuit load) and the supplied voltage is 100V. Use Zig-zag diagram to show the incident and reflected signals for 8T, then draw the time-spacing diagram for the sending end ES and IS and receiving end ER and IR

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.35P: For a lossless open-circuited line, express the sending-end voltage, V1, in terms of the...

See similar textbooks

Related questions

Q: Find V, in the network in Fig. 12/0°v(t) 2Ω -j1Ω M jΖΩ Μ 252 jΖΩ · ΠΩ 3Ω (1)2/0°A_V

A: We need to determine Vo.

Q: a 2 b 3 5 d For the given oriented graph, determine fundamental cut-set matrix and express the…

Q: Question No.84 Find the output Boolean function for the logic circuit. Ao B Di

A: Given Logic circuit:

Q: A resistor is color-coded with four bands: the first one being brown, the second being black, third…

Q: Please Help For the circuit shown in the figure, a) Determine the voltage gain (Vout/Vin). b) Make…

A: Given:A circuit, To do:a) Determine the voltage gain (Vout/Vin).b) Make the magnitude and phase Bode…

Q: that transmission efficiency increases with increasing transmission voltage or By increasing the…

A: In this question we have to prove that transmission efficiency increases with increasing…

Q: Choose the correct answer (write the answer only). The open loop voltage gain for ideal op-amp is…

A: Choose the correct answer for the following question. Only need to choose correct answer.Mostly all…

Q: Redraw the circuit, find R total, I of source, & voltage across each resistor.

A: For the given circuit the total resistance, total current from the source and voltage across all the…

Q: Describe the main features of the different types of technology that can be used for playing back…

A: Analogue recording:- Analogue implies to a continually shifting illustration of a continuously…

Q: Given the information appearing in Figure 2, determine Vce. 470 ΚΩ B =90 +22 V 9.1 ΚΩ Ic Figure 2…

Q: (a) Determine the system function H(z). (b) Determine the difference equation (I/O function). (c)…

A: Given:Block diagram of a system, Requirement:a) determine the system function H(z). (b) Determine…

Q: Q.1/ Choose the correct answer for the following questions: 1- If a system two real and equal…

A: Nature of roots: 1) Real and equal - Criticality damped2) Real and distinct - Overdamped 3) Purely…

Q: 6- T in the LTI stands for Temperature (a) (b) Terminal (c) Time (d) none of pervious answers are…

A: LTI : It is abbrevated as " Linear Time Invariant" system.

Q: Current in 10 ohm?

A: It is given that:

Q: 3. A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V…

A: Given cyclo converter in question is a step-down converter, which converts high-frequency AC voltage…

Q: 1. Determine the output voltage, Vo and the static resistance, R of the diode using graphical method…

Q: Find Vo in the following circuit

A: In this questionWe need to determine the value of output voltage Vo as shown the circuit. We are…

Q: 3.38 Obtain the impedance Z(s) of the network in Figure 3.35.

A: The total impedance of the circuit needs to be calculated and the same can be calculated by…

Q: Problem 5) Find the Fourier Transform for the following signal. 2 0 2

Q: 1. a) IN I 2 fe Figure Qla. A half-wavelength dipole antenna and EM wave generation. In the figure…

A: To find the frequency of the sinusoidal signal for maximum efficiency in converting electrical…

Q: A DC voltage source has a source resistance variable from 5 0 to 25 Q and it is connected to a load…

A: A DC voltage source has,Source resistance, variableLoad resistance,

Q: A mild steel ring has a mean circumference of 450 mm and a uniform cross-sectional area of 345…

Q: 5-32) If = 80 and V₁= co, what value of Is yields a collector current of 1 mA in Fig. 5.129?

A: The value of the reverse saturation current needs to be calculated for the given value of the BJT…

Q: LRC circuit + { +qC 1 -9 +Qmax L Dr <I а так S2 -IR-L - 1²/12 = 0 + &#+++ 4 = 0 R L (-B/L) + ⇒ 9 = A…

A: Given Data:An RLC source-free circuit with, the charge equation as,To Find:The expression for…

Q: Question 4.2-2: ' The below circuit at left includes two D flip-flops. Recall that a D flip- flop's…

Q: 2. An inductor with inductance L-0.12 H carries a linearly-changing current of I(t)=5(1-2), A. What…

A: Inductance L = 0.12 H.Current

Q: 4) The magnetic circuit of Figure 1 consists of rings of magnetic material in a stack of heigh h.…

A: Ri = 3.2 cm, Ro = 4.1 cm, h = 1.8cm and g = 0.15 cm, N = 72 turns

Q: Consider the circuit shown below a 10 ΚΩ 5 V b e 4 ΚΩ 40 ΚΩ 10 ΚΩ 12v C f 6 ΚΩ + d 4 ΚΩ 5 ΚΩ 10 ΚΩ…

A: In this questionWe need to determine the voltage at the node e and d as shown the circuit. We are…

Q: 23] Determine the output of LTI system h(n) = =(5,6,5} if if the input signal is x(n) = {1,0,5}

A: We need to find output of LTI system y(n)Where impulse response h(n)={5,0,5} start at n=0 , and…

Q: Sv A Find Vr + U X- m + sr and ir ил +m- aug YV

A: Circuit diagram is given as,

Q: Q1) Short answer questions: 1. For a solid single line to ground fault the sequence networks are…

A: Faults in the power system refer to abnormal conditions which lead to disruption in the flow of…

Q: Use the z-transform to solve the following difference equation: y[n+ 2] = 3y[n+ 1] - 2y[n], y[0] = 1…

Q: 3- A system has the unit sample response h(n) given by h(n)=-18(n+1)+18(n)-18(n-1) ATF ~TEH *?

A: Given:The impulse response of a system To determine:e) f) g)

Q: System function H(z) of an LTI system has poles at 1/2 and -2, and double zero at 0. a. Analyze and…

Q: Which one of the following rectangular values is equivalent to the polar form 20 < 55°? 16.38 +j…

A: Function in polar form is given as,

Q: Question 1 Two positive 2nC point charges, denoted by q₁ and q2, are located at (0, 4cm, 0) and (0,…

Q: What is the rms voltage output value of the ac component in a half-wave rectifier when the peak…

A: Peak voltage of half wave rectifier

Q: PROBLEM-3 ( ): Consider a unity negative feedback system with forward transfer function of K(s² - 2s…

Q: Find the position function, x(t), for the mass-spring-dashpot system with: m = 1 c = 8 k = 16…

A: Note :Here, there will be no use of it will be

Q: Design a transformer coupled class A amplifier with high efficiency to supply an output power of Po=…

A: Transformer coupled class A AmplifierIt is a type of electronic amplifier that uses a transformer to…

Q: Design a system that has a 15% overshoot and stabilizes in 2 seconds. analyze its absolute stability…

A: The maximum percentage overshoot of the system is 15%.The settling time is 2 seconds.

Q: 10- Find the sequences for the following z-transform z² z² + 4 (a) X(z) = |z| > 2, (b) X(z) = Z…

Q: It has the highest power gain but the most unstable.Please point out the answer below. 1. Fixed-Bias…

Q: A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V…

A: To draw the waveforms and perform the calculations for a single-phase to single-phase cycloconverter…

Q: 3. Determine Vx and Ix: 5mA ΙΚΩ + Vx >1.8KQ2 Ix Si Ge ΙΚΩ 20 V

Q: PROBLEM-2 ( ): Consider a unity negative feedback system with forward transfer function of 9 1…

Q: 6. For the logic diagram shown below, (a) Derive the Boolean function F. (b) Get the complement of…

Q: A DC motor is connected in a series setup. The field resistance is 12 ohms, the armature resistance…

A: A DC motor is connected in series setup.Field resistance is, ,Armature resistance is, .DC supply…

Q: Et 0.21. V0₁-0.2 |v2=0.2 Voz=0.2 Ik 24- 27 2K + 2k ли 2K 8k 2K- Yx YZ 10k миск 20k lok uy

A: The response of the circuit needs to be obtained and the same can be obtained by analysing the…

Q: Question 3 Figure shows the cross-sectional view of a coaxial cable of length 1. The radius a = 1mm,…

A: The given figure is,Figure shows the cross-sectional view of a coaxial cable of length l. The radius…

Concept explainers

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.

Question

For the lossless TL shown in below with length 1, let Zg - 620, ZR = (open
circuit load) and the supplied voltage is 100V. Use Zig-zag diagram to show
the incident and reflected signals for 8T, then draw the time-spacing diagram
for the sending end ES and IS and receiving end ER and IR

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Parameters

VIEW

Step 2: Voltage is given as

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 20 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Compensation Techniques in Transmission Line

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 50Ω lossless transmission line is terminated with a load impedance valued ZL = RL + jXL.According to what is given, a) RL for Voltage Standing Wave Ratio to be 2What should be the relationship between XL and?b) If RL = 100Ω, find the value of XL.c) Find the voltage minimum point closest to the load on the line.
For the lossless transmission line shown below, the T.L. was previously charged to E=128V and the switch is closed at t=0. If Zo= 150 ohms and RL= 450 ohms, find the following VRL at t=3To VRL at t=To First reflected voltage from the load (Vr-)
An extra high voltage transmission line of length 300 km can be approximated by a lossless line having propgation constant is 0.00127 rad/km. The percentage ratio of line length to wave length will nearly by ?
1. What is the necessary condition for matching transmission lines? In addition, what is a micro strip line? 2. For a distortion less line α = 0.02dB/m, Z0 (R0) = 60Ω and C = 0.2nF/m. Find the resistance and velocity of wave propagation. [Do not forget the units.] 3. For a finite lossless transmission line with open-circuit termination, sketch Xio vs l. Indicate where the sketch is inductive and capacitive.
Derive an expression for sag in a transmission line of equal height poles
A lossless transmission line has 100 ? characteristic impedance. The line is terminated in a load impedance of 70-j100 ?. The maximum voltage measured on the line is 200V. Find;1. The minimum current and minimum voltage on the line2. Explain how location of voltage maximum can be determined by using load reflection coefficient from the forward and backward wave.3. Using load reflection coefficient in ii., calculate the distance from the load that produce the maximum voltage and current.
A lossless transmission line is terminated by an open circuit. An incident signal travels from the source to the load gets reflected and travels all the way back to the source. It takes 4 microseconds for the signal to go from the source to the load and then from the load to the source. What is the length of the line (in m) if the propagation velocity is equal to the speed of light (in m/s)? Enter only the numerical value. No need for the unit. Use four decimal places (if the answer is not an integer).
A lossless coaxial cable with L = 0.5 uH/ft and C = 100 pF/ft is terminated by a 100-ohm resistive load. What is the characteristic impedance of the quarter-wavelength line that can be used for impedance matching?
A lossless transmission with characteristic impedance of ?0 = 100Ω and length = 52cmThe line was terminated with a load of ?? = 30 + ?50Ω. According to what is given, a) The reflection coefficient in the load and the voltage standing wave ratio on the line (GDDO)Find out.b) Find the impedance and admittance at the line input. (for ? = 750???)c) For ? = 750???, the impedance and admittance values 2cm away from the load.(It will be assumed that = ?0.)
A 500-kV, 300-km, 6()-Hz, three-phase overhead transmission line, assumed to be lossless, has a series inductance of 0.97 mH/krn per phase and a shunt capacitance of 0.0115F/km. per phase. (a) Determine the phase constant p, the surge impedance Zc, velocity of propagation v, and the wavelength of the line (b) Determine the voltage, current, real and reactive power at the sending end, and the percent voltage regulation of the line if the receiving-end load is 800 MW at 0.8 power factor lagging and at 500 kV.
For a lossless open-circuited line, express the sending-end voltage, V1, in terms of the receiving-end voltage, V2, for the three cases of short-line model, medium-length line model, and long-line model. Is it true that the voltage at the open receiving end of a long line is higher than that at the sending end, for small 1?
A three-phase power of 460 MW is transmitted to a substation located 500 km from the source of power. With VS=1. per unit, VR=0.9 per unit, =5000 km, Zc=500, and =36.87, determine a nominal voltage level for the lossless transmission line based on Eq. (5.4.29) of the text. Using this result, find the theoretical three-phase maximum power that can be transferred by the lossless transmission line.