For the multi-stage amplifier shown below,given the followingT1: K= 0.12 mA/V?, VGS(TH) = 5 V, IDQ = 6.7 mA,( VGso = 12.5 V, RD1 = 2.2 kN, (Assume rd >> RDT2: Ipss = 6 mA, Vp = -3 V, IDQ = 2.9 mA, VGSQ =(-0.95 V, Rp2 = 1.8 kQ. (Assume ra >> RD||T3: R1 = 48 kQ, R2 = 12 kQ, Rc = 1.5 kn. ro = 25kQ, and B = 120Calculate Ayj, Ay2, Ay3, and the overall voltagegain AyT20 VRD2R1Rc0.1 uFRD1T2VaT322 M20.1 uFoss = 6 mAV = -3 VT1 pBeta0.05 µFG10 MQVaso -= 100 µF2.2 kn 100 uF330 218 MQ0.82 k2 100 µF

Enhancement MOSFET: The transconductance of the Enhancement-MOSFET is determined by the following…

For the multi-stage amplifier shown below, given the following T1: K= 0.12 mA/V?, VGs(TH) = 5 V, IpQ = 6.7 mA, ( VGSQ = 12.5 V, RD1 = 2.2 kO, (Assume rd >> RD %3D T2: IDss = 6 mA, Vp = -3 V, IDQ = 2.9 mA, VGSQ = (-0.95 V, RD2 = 1.8 kQ. (Assume ra >> Rp T3: R1 = 48 kQ, R2 = 12 kQ, Rc = 1.5 kQ. ro = 25 kQ, and B = 120 %3D Calculate Av1, Av2, Av3, and the overall voltage gain AyT 20 V RD2 RI Rc 0.1 uF RDI T2 T3 22 ΜΩ 0.1 uF oss 6 mA V-3 V T1 D Beta 0.05 uF 10 MA R2 Vaso - 330 n =100 uF 2.2 ka 100 µF 18 MQ #100 uF 0.82 k2

For the multi-stage amplifier shown below, given the following T1: K= 0.12 mA/V?, VGs(TH) = 5 V, IpQ = 6.7 mA, ( VGSQ = 12.5 V, RD1 = 2.2 kO, (Assume rd >> RD %3D T2: IDss = 6 mA, Vp = -3 V, IDQ = 2.9 mA, VGSQ = (-0.95 V, RD2 = 1.8 kQ. (Assume ra >> Rp T3: R1 = 48 kQ, R2 = 12 kQ, Rc = 1.5 kQ. ro = 25 kQ, and B = 120 %3D Calculate Av1, Av2, Av3, and the overall voltage gain AyT 20 V RD2 RI Rc 0.1 uF RDI T2 T3 22 ΜΩ 0.1 uF oss 6 mA V-3 V T1 D Beta 0.05 uF 10 MA R2 Vaso - 330 n =100 uF 2.2 ka 100 µF 18 MQ #100 uF 0.82 k2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the common-emitter amplifier circuit shown in the figure, Vcc=9V, R1=27kΩ, R2=15kΩ, RE=1.2kΩ and RC=2.2kΩ. The transistor has β=100.a-) If Rsig=10kΩ and RL=2kΩ, calculate the IE value of the amplifier.b-) For small signal analysis of the transistor, find the value of Rin by deriving the π-modelc-) Calculate vo/vsig and io/ii.
4--In the given circuit, n MOSFETs are used.Q1, Q2,….. Parameters of Qn MOS transistors Vt=1V, γ=0, λ=0,μnCox=200μA/V2 and (W/L)1=(W/L)2=….=(W/L)n=20a) VGS=?, ID=?, gm=?b) Find the input and output impedance.c) Find the voltage gain.
(a) What are the Q-points for the transistors in the amplifier as shown if VDD =5V, VSS =5 V, RSS =2.4 kΩ, and RD =2.4 kΩ? Assume Kn =400 μA/V2 and VT N =0.7 V. (b) What are the differential-mode gain, common-mode gain, CMRR, and differential-mode and common-mode input resistances?
In the circuit in the figure, VGSQ = 6.8 V, IDQ = 2.4 mA, VGS(Th) = 3.3 V, k = 0.4x10-3 A/V2, RD = 5.6 kΩ, RF = 2.2 MΩ and rd = 25 kΩ. Accordingly, when a RL = 0.1 kΩ load is connected to the output of the circuit, what will be the voltage gain of the circuit? NOTE: MOSFET output resistance must be taken into account in rd calculations
(a) What are the Q-points for the transistors in the amplifier as shown if VDD = 9 V, VSS = 9 V, ISS = 40 μA, RSS = 1.25 MΩ, and RD = 300 kΩ? Assume Kp = 200 μA/V2, γ = 0.6 V0.5, 2φF = 0.6 V, and VTO = −1 V. (b) What are the differential-mode gain, common-mode gain, CMRR, and differential-mode and common-mode input resistances?
Design a Single-Stage Common Emitter Class A Amplifier Specifications:Voltage Divider Bias Circuit Supply: Any value from 10Vdc to 24VdcLoad: 1kΩVoltage Gain: Any value from 80 to 400Lower Cutoff Frequency: 100 HzSinusoidal source (zero internal resistance): 50mVp-pTransistor: Si, β = 75 • Base-Collector capacitance = 8pF • Base-Emitter Capacitance = 25pF a) compute for the biasing resistances.b) determine the dc transistor terminal voltages and transistor currents.
In the circuit in the figure, IDSS = 12 mA, VP = -8 V, VGSQ = -2.4 V, IDQ = 4.12 mA, Rsig = 10 kΩ, RG = 100 kΩ, RD = 2.4 kΩ, RS = 470 Ω, RL = 33, It is known that 9 kΩ and rd = 20 kΩ. What will be the voltage gain of the circuit? NOTE: The FET output impedance is rd = 20 kΩ and must be taken into account in the calculations.
The dc bias circuit for a common emitter amplifier is shown in the figure. In the circuit, Vcc=15v,RB1=20k Ω,RB2=100k Ω,Rc=5.1k Ω,and RE1=1k Ω, Assume that when the transistor is on, the voltage drop from base to emitter VBE=0.7v. Also assume that β= ∞, which implies that the base current can be considered zero (IB=0) in your calculations. Solve for the base voltage VB. Solve for the emitter voltage VE. Solve for the emitter current IB. Solve for the collector current IC
For the multi-stage amplifier shown below, given the following T1: K = 0.12 mAV ?, VGS (TH) = 5 V, IDQ = 6.7 mA, VGSO = 12.5 V, RD1 = 2.9 kQ, (Assume rd >> Rp) % 3D% 3D T2: Ipss = 6 mA, Vp = -3 V, Ipo = 2.9 mA, VGSQ = -0.95 V, RD2 = 2.4 kQ. (Assume rd >> Rp)% 3D T3: R1 = 48 kQ, R2 = 12 kQ, Rc = 2.2 kQ. ro = 25 kQ, and B = 140 Calculate Ay1. Ay2, Ay3, and the overall voltage gain Avt
For the amplifier as shown, VDD = 12 V, VSS = 12 V, ISS = 20 μA, and RD = 820 kΩ. Assume IDSS = 1 mA and VP = +2 V. (a) What are the output voltages υo for the amplifier for υ1 = 0V and υ1 = 20 mV? (b) What is the maximum permissible value of υs?
If the circuit of problem 2 is configured as a common-emitter amplifier, calculate the resulting voltage and current gain. Assume a load resistor of 1k ohm. Circuit of problem 2: determine the operating point of a universal trasnsistor DC bias cirucit when Vcc=15V, R1=10k ohm, R2=2.2k ohm, Rc=680 ohm, Re=100 ohm. Assume beta (b)=200 and Vbe=0.72V.
(a) What are the Q-points for the transistors in the amplifier as shown if VCC = 15 V, VEE = 15 V, IEE = 400 μA, βF = 100, REE = 270 kΩ,RC =47 kΩ, VA=∞, and βF =100? (b) What are the differential-mode gain, common-mode gain, CMRR, and differential-mode and common-modeinput and output resistances? (c) Repeat part (b) for VA = 50 V.