For the state of plane stress as shown in the Figure: Construct the Mohr's circle. Determine the principal stresses. Find the orientation of the principal plane. Compare the results of (b) and (c) with equation method. 12 MPa 6 MPa 8 MPa

For the state of plane stress as shown in the Figure: Construct the Mohr's circle. Determine the principal stresses. Find the orientation of the principal plane. Compare the results of (b) and (c) with equation method. 12 MPa 6 MPa 8 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.25P: The stresses at a point on the down tube of a bicycle frame are trx= 4800 psi and t = -1950 psi (see...

See similar textbooks

Related questions

Q: A 3-mm-diameter and 5-m-long electric wire is tightly wrapped with a 2-mm- thick plastic cover…

Q: Q12/ An electric motor drive an exhaust fan through an open belt drive. Following data are provided:…

A: INTRODUCTION: In this problem, we will determine the breadth of the belt that is subjected to stress…

Q: The percent rating of water tube boiler is 200 %, factor of evaporation is 1.10, and heating surface…

Q: 5. Find the current density for electrochemical machining nickel; 1. Round Through hole 2. Square…

Q: Recall the two coupled masses undergoing linear oscillations in Example 8, p.22-25. Solve a simple…

A: For solution refer below images.

Q: The rigid bar AB attached to aluminum and steel rods, is horizontal before the load P is applied.…

A: Aluminum: L= 3 m= 3000 mmA= 500 mm2E= 70 GPa= 70000 MPa Steel: L= 4 m= 4000 mmA= 300 mm2E= 200 GPa=…

Q: A Carnot engine receives 100 Btu of heat from a reservoir at 600oF and ejects at 60 Btu of heat.…

Q: is it necessary to have the correct temperature variations in the specific gravity test?

A: Determination of specific gravity of any solution is depend upon on temperature and pressure.

Q: 3. What makes EDM become a key in tool and die making machine tool ?

A: The main reason of using EDM in die making process are:-

Q: Refrigerant 134-a enters a compressor at 180kPa as a saturated vapor with a flow rate of 0.4m³/min…

Q: A simple saturation cycle using ammonia between pressures of 10 psia and 165 psia is to be replaced…

Q: Disks A and B have a mass of 6kg and 4kg, respectively. They are sliding on the smooth horizontal…

Q: SHEET ONE Q1: Determine the pressure in the pipeline if the atmospheric pressure is 80 kPa. 2 in 10…

A: Find the pressure in the pipe line

Q: Q3) The path of a projectile is shown in figure (3). If the object has an initial velocity of Vo-30…

Q: unit of a is

A: Given; Van der Walils equation of state is; p±v-b=RT where, p= pressure v= specific volume T=…

Q: Disks A and B have a mass of 6kg and 4kg, respectively. They are sliding on the smooth horizontal…

Q: y = 2x ; x = 0; y = 2; y = 6 axis OX. Find the moment of inertia.

Q: Consider an ideal Rankine thermodynamic cycle with H2O as the working fluid. From the following…

Q: a) Briefly explain why HCP metals are typically more brittle than FCC and BCC metals. b) Two…

Q: There are two springs attached to a mass with an unknown weight. The springs have a stiffness of k =…

A: Sd

Q: 2. A bracket, as shown in Fig. 2, carries a load of 10 kN. Find the size of the weld if the…

Q: The moment of inertia of the cross-section about X-X axis is

A: Given data : Depth is denoted by d Width is denoted by b To find : Moment of inertia about XX axis

Q: 9 7-158 An iron block of unknown mass at 85 C is dropped into an insulated tank that contains 0.02…

Q: 21: For the figure shown, if p=300N and the distance d between the force and the centroid of the…

Q: What is the pressure at the bottom of 0.5m height fluid if the container moves 5m/s2 upward? Fluid…

Q: At a power plant, superheated steam at 560°C is used to drive a turbine for electricity generation.…

A: Given Maximum temperature, Tmax = 560°C Minimum temperature, Tmin = 38°C Find Energy…

Q: Strain gage A thin wall spherical vessel, shown in Figure, contains a gas under pressure p. The…

Q: A solid circular shaft of diameter 220 mm is to be replaced by a hollow shaft in which the ratio of…

Q: what is the value of Cx?

A: Fx= 12.662 kN. Using equilibrium condition in x direction for member FC.

Q: To prevent dehydration in air blast freezing method the air velocity under controlled :time should…

A: Ans: Third option is correct. 160

Q: Q2: A composite component consists of a glass fiber and an epoxy matrix. The glass fiber weight…

Q: 4. A tensile tests is performed to determine the mechanical properties of and aluminum alloy. The…

A: INTRODUCTION: True stress and strain are not the same as engineering stress and strain. True stress…

Q: Ex) Using The method of dimensions, deriv an expression for rate of flow (CP) of aliquid Through a…

Q: 120 kg 60 A B 50 kg

Q: Convert 2.5 bar pressure in equivalent column of mercury and water.

Q: 5 kN 8 kN/m 5 kN-m -2 m 2 m * A) Construct the shear and bending moment diagrams. The reactions: on…

Q: Why is it necessary to measure the viscosity of a liquid (or a gas)? Give practical examples where…

A: The viscosity of any liquid is defined as the resistance of flow of fluid. When there is a relative…

Q: Q2) In figure below, the pressure p₂ = 30,4 KN/m², whereas the velocity of the water is V₂ = 2 m/s.…

Q: Q4: What the meaning of 1. Static head of Centrifugal Pumps Manometric head of Centrifugal Pumps 2.…

Q: What about v2 at theta = 90

A: In this problem, it is asking what will be the value of v2 when θ=90°.

Q: 71 For the system shown, What is the flow direction? What kind of machine is at A? Do you think both…

A: Solution is attached below:

Q: 16cm โรงเร I 1 1cm <- Scr Icm

Q: SHEET ONE Q1: Determine the pressure in the pipeline if the atmospheric pressure is 80 kPa. Air 2 in…

A: Q-1 find the pressure in the pipeline Q-2 find the height (h).

Q: Find the discharge value Area=0.9 m2 Velocoty=0.2 m/s

A: We know discharge Q = Area × Velocity Q = A× V

Q: process planning is known as

A: Given; Following are the option given, Where, Given question is; During development of a product…

Q: 1 9 The following data represents the relation between the heat capacity of a plate (q) and time…

Q: • Ex) A (1/5) scale of a vehicle is to be tested, One in a wind tunel, in a water tunnel, Determine…

A: Given data Scale = 1/5 Speed of prototype = 120km/h Kinematic viscosity For water = 1.002×10^(-6)…

Q: An ammonia refrigeration compressor takes its suction from the evaporator at a temperature of -20oF…

A: Given Enthalpy, h,2 = 1,568 kJ/kg At 10oC: hf,3 = 246.531 kJ/kg At -28.9oC by…

Q: In white cast iron, the carbon is in combined form as .......... O cementite iron O silicon оос…

Q: A rigid bar, hinged at one end, is supported by two identical springs as shown in figure. Each…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
-18 through 7.3-22 An element in plane stress (see figure) is subjected to stresses o, a., and (a) Determine the principal stresses and show them on a sketch of a properly oriented element. (b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element. 7.3-18 a=2I50kPa, ay=375kPa.Txy.=-460kPa
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
The stresses at a point on the down tube of a bicycle frame are trx= 4800 psi and t = -1950 psi (see figure). It is known that one of the principal stresses equals 6375 psi in tension, (a) Determine the stress (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented clement.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.