For the state of plane stress shown below, construct a Mohr's circle and determine:- (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the maximum in-plane shear stress at the point and the corresponding average normal stress (d) the orientation of the maximum in-plane shear stress (e) show the results on elements 700 kPa 100 kPa 400 kPa

For the state of plane stress shown below, construct a Mohr's circle and determine:- (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the maximum in-plane shear stress at the point and the corresponding average normal stress (d) the orientation of the maximum in-plane shear stress (e) show the results on elements 700 kPa 100 kPa 400 kPa

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
Consider the nonprismatic cantilever beam of circular cross section shown. The beam has an internal cylindrical hole in segment 1; the bar is solid (radius r ) in segment 2. The beam is loaded by a downward traingular load with maximum intensity q0 as shown. (a) Find expression for maximum compressive stress at point 1. (b) Find expression for maximum tensile stress at point 1.
Direct stresses of 120 N/mm2 (tension) and 90 N/mm2 (compression) are applied at a particular point in an elastic material on two mutually perpendicular planes. The principal stress in the material is limited to 200 N/mm2 (tension). Calculate the allowable value of shear stress at the point on the given planes. Determine also the value of the other principal stress and the maximum value of shear stress at the point using Mohr’s Circle.
The figure shows the stress condition of an I-section beam at point A. With the Mohr circle method; 1-)Calculate the principal stresses, location and angle. 2-)Calculate the stress components that will affect the plane obtained by rotating the figure counterclockwise 25.
The cross section of the AB part of the welded pipe part given in the figure is a hollow pipe and the cross section of the BC part is a circle with a solid body. The inner diameter of the pipe section is 20mm and the outer diameter is 28mm, while the diameter of the full body part is 12mm. Determine the average normal stress at the D and E points accordingly.
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of the external diameter of 3.6 cm and an internal diameter of 2 cm. The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.5 cm from the neutral axis Solution: (i) The moment of inertia = Answer and unit for part 1 ii) The radius of curvature is Answer and unit for part 2 (iii) The maximum bending stress is Answer and unit for part 3 iv) The bending stress at the point 0.5 cm from the neutral axis is
3. Two plates are connected by bolts as shown in the figure. Compute the maximum axial stress that each plate will handle. The allowable shear stress of each bolt is 50MPa and the diameter of each bolt is 20 mm
Defferentiate the following terms; 1.Resilience and proof resilience 2.proof resilience and modulus of resilience B)A solid beam ABC circular in section has varying sections.portion AB is 6m in length and diameter of 250mm while portion BC is 2m in length and section diameter of 100mm.The beam is subjected to a sudden tensile load.if the maximum stress induced is 400MN/m^2.Determine the strain energy stored in the beam.Take E=200GN/m^2
Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.8 GPa. Bar (2) is a nylon material that has an elastic modulus of 1.9 GPa. Each bar has a cross-sectional area of 900 mm2. Using L = 395 mm and Δ = 4.6 mm, what magnitude of load P will cause the normal stress in each bar to be the same value?
Please answer this question, An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa
Determine the principal stress, the maximum in-plane shear stress, and average normal stress. Specify the orientation of the max stress element in each case. Solve the question using Mohr Circle. (Picture Attached) σx = 60psi σy = 120psi τxy = 30psi