For the steel frame below, assume the combined factored load on this floor-bound by A1A3C3C1 is 8.5 kPa. For this question, ignore the self-weight of the framing members. Determine the load acting on: a) beam A1A2 b) beam B1 • c) beam A3B3 • d) column C2 1 2 (3 25m 22m EQ 5 m B1 G2 G1 EQ 5 m C2 (B 5 m EQ EQ 5 m I- H-

For the steel frame below, assume the combined factored load on this floor-bound by A1A3C3C1 is 8.5 kPa. For this question, ignore the self-weight of the framing members. Determine the load acting on: a) beam A1A2 b) beam B1 • c) beam A3B3 • d) column C2 1 2 (3 25m 22m EQ 5 m B1 G2 G1 EQ 5 m C2 (B 5 m EQ EQ 5 m I- H-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel beam cross cross section is assembled as shown by bolting the channel, C200 x 27.9 through its web on the wide flange, W200 x 35.9. The beam is 4 m span and is simply supported loaded with a uniformly distributed load of intensity 20 kN/m throughout its span and a concentrated load, P kN = 52, at the mid span. If the diameter of the bolts is 22 mm. a) compute for the moment of inertia of the cross section b) determine the minimum bending stress in the beam c) calculate the spacing of bolts (pitch) if the allowable shearing stress for a bolt is 100 MPa. Kindly write legibly. Thank you.
A W21 x 50 spans11.0 m on a simple span. The compression flange is laterally supported at the third points. A36 Steel is used. a) Determine the allowable bending stress of this beam. b) Determine the allowable superimposed uniformly distributed load be place on this beam.
A short, braced column is subjected to an ultimate applied axial load of 3000 kN and a nominal moment only. Using the design data given: Design the main steel reinforcement with minimum size of square column to carry the load without failure Design Data: Characteristic strength of concrete fcu = 40 N/mm2 Characteristic strength of reinforcing steel fy = 460 N/mm2 Clear height between the end restraints about both axes = 5.0 m
A T-beam that traverses the center of a floor system for which bw = 300mm and d=550 mmm. The beams are 4.8 m long and spaced at 3 m on center and the slab thickness is 100mm. Determine the required steel area if the dead load moment including its own weight is 400 kN-m, live load moment is 500 kN-m, f'c = 28 Mpa and fy = 414 Mpa.
A flitch beam is composed of two 50x300mm planks reinforced with a 12.5mm steel plate as shown. Assume that continuous lateral support is furnished by a floor system supported by the beam. Use A36 steel with an allowable bending stress of 150 MPa, Fy = 250 MPa. Es = 200,00MPa, Ew = 7692MPa, fw = 4.3 MPa. The beam is on a simple span of 4.8m and supports a uniformly distributed load of 7.3 kN/m which includes the weight of the beam. Allowable stresses for shear: Steel: fv = 0.60Fy MPa Wood: fv = 0.58 MPa Determine the following: a.) The resisting moment of the flitch beam b.) The applied moment to the flitch beam c.) The shear capacity of the flitch beam
Draw FBDs showing loads and reactions for members B2 andB3 and determine all the loads acting on member G2Assume a dead load of 50 psf and a live load of 50 psf and neglect the own weight of the structural members.
A simply supported beam 300 mm wide, 500 mm deep and spans 5.2 m supports a service super imposed dead load of 12 kN/m and service live load of 8 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. 1. Determine the maximum ultimate moment (in kN-m) the beam must resist using load combination of NSCP 2015 a. 116.64, b. 115.02, c. 109.44, d. 106.54 2. Determine the required depth of uniform stress block (in mm) upon crushing of concrete when ultimate load is applied. a. 60.54, b. 56.52, c. 54.92, d. 65.54 3. Determine the required amount of tensile reinforcement (in mm^2) a. 775, b. 729, c. 781, d. 708
A 4m simply supported beam (b = 230mm, h= 550 mm) will be used to carry a uniformly distributed load of WDL = 50 kN/m and WLL = 40 kN/m over its span. If the beam has an f'c of 20 MPa, fy of 415 MPa, effective depth of tension steel of 500 mm, effective depth of compression steel of 50 mm, determine if the beam can carry the loads. The beam is reinforced with 2-16mm bars on top and 5-20mm bars at the bottom.
Q3/ A 7.0 m simply supported rectangular beam has a width of 450 mm and a depth of 850 mm. Supports, in addition to its own weight, a 40 kN/m dead load and a 35 kN/m live load. Knowing that fc' = 21 MPa and fy = 420 MPa, Find the required area of steel to support the applied loads
A steel beam is made up of a wide flange section whose total depth is 600mm, width of the flange is 300mm, flange thickness of 20mm and moment of inertia Ix = 1.16x109 mm4 . Its web thickness is 10mm and has a simple span of 9m. A 40 kN/m uniform load is loaded throughout its span and 200kN load acting at midspan. Allowable bending stress of the beam is 148.8 MPa. Situation No.1.1 Determine the length of top and bottom reinforcing plates if necessary
A steel beam is made up of a wide flange section whose total depth is 600mm, width of the flange is 300mm, flange thickness of 20mm and moment of inertia Ix = 1.16x109 mm4 . Its web thickness is 10mm and has a simple span of 9m. A 40 kN/m uniform load is loaded throughout its span and 200kN load acting at midspan. Allowable bending stress of the beam is 148.8 MPa. Situation No. 1 1. Determine the required section modulus without exceeding the allowable bending stress. 2. Determine the section modulus of the wide flange. 3. Determine the width of top and bottom reinforcing plates 12mm thick if necessary. 4. Determine the length of top and bottom reinforcing plates if necessary.
A 6.5m long column in an existing building is part of a braced frame in both xx and yy planes of the cross section. It is fixed at the base and pinned at the top about both axes. In addition, the column is laterally supported perpendicular to its weak axis at a height 3.5m from the base. The column is a W (given designated steel section below) with Fy=415MPa. a. Determine the design compressive strength of the column. b. Is the column adequate to carry an axial compressive load of 400kN?