For the truss and loading shown, determine the force (lb) of member DG, if P= 30149 lb, Q = 35358 lb, y = 6.17 ft . Round off only on the final answer expressed in 3 decimal places. 0004.png ... В D F H y C E 4 panels at 10 ft = 40 ft

For the truss and loading shown, determine the force (lb) of member DG, if P= 30149 lb, Q = 35358 lb, y = 6.17 ft . Round off only on the final answer expressed in 3 decimal places. 0004.png ... В D F H y C E 4 panels at 10 ft = 40 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the forces in members BC, HC,HG, and DF using Section Method. 140 kN sl ISKN Am Ay: 0 KN 3…

Q: For the truss and loading shown, determine most economical cross-sectional area (in in2) of member…

Q: Q2(5) , Determine the force in members ab,dh,dg, eg, hi,hj, & hk of truss shown in figure ? 2m 3m in…

A: Given figure shows a truss. It is required to calculate the forces in member ab, dh, dg, eg, hi, hj…

Q: For the truss and loading shown, determine most economical cross- sectional area (in in2) of member…

A: Given data in question Load Span member length Stress To find out Area of member DG

Q: Problem #1 4) 10k For the plane truss at right: 3. a. Determine all zero-force members and state the…

Q: 1 2,236 Ibs. 750 ppf 750 ppf B В A D 5' 44'. 16'

Q: 12 B E + 1200 Ib 12 A F 3' C 3' 2400 Ib 1200 Ib

Q: Determine the spacing of shear reinforcement (S) between stirrups in reinforced concrete beam.…

Q: Ass #2. Solve the following Problems. 1. Using method of sections, determine the forces in members…

Q: For the truss loaded as shown determine the forces in members FH, GH, and GI in kilonewtons. Use the…

A: Consider the figure,

Q: The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 3 kN,…

Q: Determine the vertical displacement of joint A. Each A992 steel member has a cross-sectional area of…

A: Given :- A truss is given with each A992 steel member has a cross-sectional area of 400 mm2 Point…

Q: 1.) Determine bar force members EB, EC, and DC using method of sections. You may not copy the…

Q: 2. Use the method of sections to determine the forces in members AB, FG, AH, and GH. State whether…

A: given that bruss method of sectionforces in AB,FG,AH,GHFBD of given bruss , after section cut,…

Q: Part 2 A Pratt roof truss is loaded as shown. Using the method of joints and the method of sections,…

Q: 2. Determine the foreces in the members marked by "x" in the truss loaded as shown at the right. Use…

A: Given Structure( truss ):

Q: Calculate for the axial force at beam BF in kN

Q: D F H y E G B.

Q: normal Ja-25° K → P= AB kN

A: Given data: P=53 KNA=1200 mm2α=25o Calculating normal stress on the plane a-a:…

Q: 5. Using the method of sections, determine the members EF and GI of the truss shown. Show your…

A: Given- A simple truss is given To find- FEF FGI

Q: Using the method of sectiɔns, determine the force in members BD, CD and CE of the roof truss shown.…

Q: Using the method of sections and cut line aa, = calculate the force FCF in member CF of the truss if…

Q: Using METHOD OF SECTIONS. Determine the force in members DF, DG, and EG given the figure and data…

A: Using method of section

Q: APIENT 2. Use the method of sections to determine the forces in members AB, FG, AH, and GH. 3 ni…

Q: 4. Determine the forces in each members. Use Method of joint and/or method of section. 660 N 560 N…

A: Determine the forces in each members. Use Method of joint and/or method of section.

Q: The truss shown below is loaded as follows P1=10kN, P2=30kN, and P3=25kN. Using the method of…

Q: P В D F H y C E G 4 panels at 10 ft = 40 ft

Q: For the truss and loading shown, determine most economical cross- sectional area (in in2) of member…

Q: (21 - 24 ) Evaluate the given Fink Truss using method of sections. Answer the following questions if…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: Q 3: Draw A. F. D., S. F. D., and B. M. 12 kN/m D. for the frame shown in Fig. (3) 100 kN B. 4 m…

A: We have to draw axial force, shear force and bending moment diagram

Q: Learning Goal: To use the method of sections to determine the force in a truss member, Let point O…

Q: Use the method of sections to determine the forces in members AB, FG, AH, and GH. State whether the…

A: Consider the sign of Tension as positive and compression as negative Consider the members on the…

Q: 10 kN 20 kN E F 20 kN D 20 kN G 10 kN В L 300 30 A M K J 6 panels at 5 m

Q: Quiz 4- Truss Analysis Determine the forces in members BC, HC, HG, and DF using Section Method. 40KN…

Q: Using METHOD OF SECTIONS. Determine the force in members DF, DG, and EG given the figure and data…

Q: For the truss and loading shown, determine the force (Ib) of member EG, if P = 28005 Ib, Q = 35833…

A: Find force in member EG?

Q: Using the method of sections and cut line aa, = calculate the force FCF in member CF of the truss if…

Q: 34 - A support is a fixed, B support is a sliding joint. loads M= 30 kNm, P1= 12 kN, P2= 13 kN,…

A: ΣFy = Ay + By = 0 Ay + By - 12 - 12 - 13 - 7 -0.5 * 7 * 3 Ay + By = 54.5 KN Taking moment at A 12*2…

Q: 2.62 Calculate the beam reactions at supports A, C, and D. Draw all appropriate FBDS. 300# A 200#…

A: Free body diagram of the member AB.

Q: Using the method of sections, determine the force in members BD, BE and CE. D F 50 kN В 4 m A H E G…

Q: In the simply-supported beam shown in (Figure 4), di = 14 m, d2 =7 m, and F = 15 kN. Figure < 4 of 4…

A: Shear Diagram For the Beam is Given Below:Support Reactions at A and B are Raand Rb.Use Vertical…

Q: Using METHOD OF SECTIONS. Determine the force in members DF, DG, and EG given the figure and data…

Q: 7kN 8kN 9kN By D A C E G H 3.00m 3.00m 3.00m 3.00m

Q: 16 - The stair beam in the figure will have support reactions. A support is a fixed, B support is a…

A: Roller support gives reaction only in one direction and is free to move in the direction…

Q: 3. Using the Method of Sections, determine the forces in the members listed in the table below for…

Q: P В D F H y C E G 4 panels at 10 ft = 40 ft

Q: Problem01. Determine the force in member AD,DC andEC using method of Sections. Indicateifthe member…

A: In method of sections we cut the member and analyse the section as a separate rigid body.

Q: Determine the forces in members specified below of the loaded symmetrical truss. Use method of…

Q: 3. Using the method of joints, determine the force in each member of the truss shown. State whether…

Q: roblem 2. Using method of sections, determine the kind and amount of stress in members U,U,„U,L, and…

A: To find force in members of truss

Question

help me to answer this

For the truss and loading shown, determine the force (lb) of member DG, if P= 30149 lb, Q = 35358 lb, y = 6.17 ft. Round
off only on the final answer expressed in 3 decimal places .
0004.png
...
P
В
D
F
H
y
C
E
4 panels at 10 ft = 40 ft
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Interior finishes for wood light frame construction

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
Using portal method, Calculate for the shear force in kN at member FC a = 12.6 kN, b = 27.2 kN, c = 3.5 m, d = 5.0 m, e = 5.4 m
A truss joint shown consists of a bottom chord C made up of two angles and web members A and B each carrying the given loads. Using rivets with allowable shearing and bearing stresses of 120 MPa and 600 MPa respectively, determine the number of rivets for members A, B, and C. thickness = 9.5 mm ; diameter = 18 mm
The electric power transmission tower supports two wires that apply 18 kN verticalforces, and the 36 kN horizontal force crudely models wind loading during astorm. Use the method of sections to determine the force in members IF, IM andBD.
Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
A truss joint shown consists of a bottom chord C made up of two angles and web members A and B each carrying the given loads. Using rivets with allowable double - shearing and bearing stresses of 120 MPa and 600 MPa respectively, determine the number of rivets for members A, B, and C. thickness = 9.5 mm ; diameter = 18 mm
Determine the elongation of the tapered rectangular rod if E=170GPa.
The I-section displayed is made up of five boards (four 40x40mm and one 40x380mm). If the allowed stress in bending is 12 MPa and in shear is 0.8 MPa, calculate the load (p in kN/m) that this beam can carry over a span of 4 m, dispersed over its length.
The T section shown is formed by joining two rectangular pieces of wood together. The beam is subjected to a maximum shearing force of 60 kN. All dimensions are in mm . A.) Which of the following gives the moment inertia in x 10^6mm^4 at the neutral axis? Choices: 8.56,14.26,10.57,21.52 B.) Which of the following gives the shearing stress at the neautral axis? Choices: 3.21,4.64,3.95,4.28 C.) Which of the following gives tge shearing stress in MPa at the junctiin between two pieces of wood? Choices: 31.78,21.42,28.32,16.52
31 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, the shear force at point E T=? a) 2B) 4C) 14D) 0E) 6
For the truss and loading shown, determine the magnitude of the force (lb) in member CE, if P = 30322 lb, Q = 34406 lb, and y = 6.9 ft. Round off only on the final answer expressed in 3 decimal places .
Trace the load, draw FBD and calculate support reactions for the following elements: Beam B2 Beam B3 Girder G1