For the truss loaded as shown determine the forces in members FH, GH, and GI in kilonewtons. Use the method of sections. (Due to the nature of this problem, do not use rounded intermediate values in your calculations 3.0 kN 1.6 kN A В 2.5 m 8.8 kN 3.6 kN D 2.5m 3.6 kN V F 2.5m 3.6 kN V H 2.5m 1.6 kN V 2.5 m 2.5m

For the truss loaded as shown determine the forces in members FH, GH, and GI in kilonewtons. Use the method of sections. (Due to the nature of this problem, do not use rounded intermediate values in your calculations 3.0 kN 1.6 kN A В 2.5 m 8.8 kN 3.6 kN D 2.5m 3.6 kN V F 2.5m 3.6 kN V H 2.5m 1.6 kN V 2.5 m 2.5m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the force on Member CH in kips by method of sections. If the given 30kip load at joint J and 25kip loads at joint B, C,D, E Express your answer in 2 decimal places. Include (-) negative sign if the force is compression.
Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn
26 -The stair beam in the figure will have support reactions. A support is a fixed, B support is a sliding joint. loads P1= 15 kN, P2= 30 kN, dimensions a = 2 m, b = 6 m, c = 4 m. Accordingly, Ax = ?A) 30B) 18.75C) None.D) 3.75E) 0
The length of top chord from A to Dis 24 m which is equally divided by 4 spons Determine the value of forces of the following members and identify if T or C: FN = 95 kN MN = 86 kN SN = 79 KN
16 -The stair beam in the figure will have support reactions. A support is a fixed, B support is a sliding joint. loads P1= 15 kN, P2= 30 kN, dimensions a = 2 m, b = 6 m, c = 4 m. Accordingly, Bx = ?A) 3.75B) None.C) 18.75D) 0E) 30
An I beam whose flange width is 357mm, flange thickness is 15mm, web thickness is 20mm, total depth of 450mm and Fy of 248MPa is to be used to carry a uniform load all throughout its length, 3m. 1. What is the allowable bending stress? a. 153.69 MPa b. 161.75 MPa c. 192.69 MPa d. 168.23 MPa 2. Determine the moment of inertia of the section. a. 0.732 x 10⁹ mm⁴ b. 0.517 x 10⁹ mm⁴ c. 0.630 x 10⁹ mm⁴ d. 0.810 x 10⁹ mm⁴ 3. What is the maximum safe uniform load that the beam could carry? a. 402.58 kN/m b. 164.6 kN/m c. 476.56 kN/m d. 541.6 kN/m
For the beam shown below, given that AB = 5 m, AC = 1 m, and P = 5 kN, draw the FBD, shear & momment diagram, and then calculate the magnitude of the internal bending moment at cross-section C of the beam: ____ kN m. Calculate your solution to 1 decimal place.
For the beam loaded as shown, determine EIy midway between the supports.
Problem 11.075 - Determine the vertical deflection of point C caused by the load P Each member of the truss shown is made of steel and has a cross-sectional area of 5 in2. Using E = 29 × 106 psi, determine the vertical deflection of point C caused by the 10-kip load P. (Round the final answer to three decimal places.) The vertical deflection of point C is in. ↓.
A beam AB, 1.2m long, is simply-supported at its ends A and Band carries two concentrated loads, one of 10 kN at C, the other 15 kN at D. Point C is 0.4m from A, point D is 1 m from A. Draw the S.F. and B.M. diagrams for the beam inserting principal values.
Answer in 3 decimal places please. Thank you. The cantilever beam shown is subjected to a concentrated load of P. The cross-sectional dimensions of the wide-flange shape are also shown, where bf = 7.00 in., d = 14.0 in., tf = 0.475 in., tw = 0.350 in.(a) Compute the value of Q that is associated with point K, which is located yk = 3.5 in. above the centroid of the wide-flange shape.(b) If the allowable shear stress for the wide-flange shape is τallow= 13 ksi, determine the maximum concentrated load P than can be applied to the cantilever beam.Calculate the cross-sectional area of the top flange (1), the bottom flange (2), and the web (3).Answers:A1 = in.2.,A2 = in.2.,A3 = in.2. Determine the location of the y direction centroids of the top flange (1), the bottom flange (2), and the web (3), with respect to the bottom of the cross-section.Answers:y1 = in.,y2 = in.,y3 = in. Determine the centroid location in the y direction for the cross-section…
Check the midspan deflection of the W12 x 40 girder shown? Neglect the weight of the girder. Assume E = 29 x l0^6 psi and Ix = 310 in^4. Allowable deflection for the total load = (span/240).