For the two systems shown below (not to scale), the following are given. • Ah is the same for both systems. • The length of k₂ soil is twice the length of k₁ soil. • The cross-sectional areas of the soil samples are the same. • k₂ = 2k₁ (Permeabilities) • q₁ = 100 cm³/hour Find q2 9₁ Ah 92 k k₂

For the two systems shown below (not to scale), the following are given. • Ah is the same for both systems. • The length of k₂ soil is twice the length of k₁ soil. • The cross-sectional areas of the soil samples are the same. • k₂ = 2k₁ (Permeabilities) • q₁ = 100 cm³/hour Find q2 9₁ Ah 92 k k₂

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.12P

See similar textbooks

Similar questions

Problem 4. A 1-m³ sample of moist soil weighs 2000 kg. The water content is 10%. Assume is 2.70 Mg/m³. With this information, fill in all blanks in the phase diagram below. V₁ = V₂ Vw Air Water- Soil M₂ Ms M₁ =
The results of the particle-size analysis of a soil are as follows: % passing no 10 sieve = 100, % passing no 40 sieve = 80 and % passing no 200 sieve = 65. The liquid limit and plastic limit of the soil are 30 and 15 respectively. What is the group index of the soil?a. 5b. 7c. 8 d. 9
Results from a liquid limit test conducted on a soil are given below. a. Determine the liquid limit of the soil. b. If it is known that the PI = 6.5, what would be the plastic limit of the soil? c. Determine the liquidity index of the soil if win situ = 23.8%
Q2: A 0.01 m' of saturated soil sample has a unit weight of 1.6g/cm3. After it is dried in the oven, the weight of the soil sample reduced to 13.5kg. Use a phase diagram, determine the following: Weight of water for the saturated soil, Ww Water content, wc Ws WATER Void ratio, e Porosity, n SOLID befare trng W. Va SOLID efter ening
A sample of clay (weight = 13.2 N) is brought back from the field and trimmed to the following dimensions: height = 150 mm and diameter = 75 mm. The water content has been determined to be 25%. The Gs value for the solids is 2.75. Show and complete your phase diagram and find the following parameters: a. Draw a phase diagram b. Complete the phase diagram by finding the parameters of VT, Va, Vw, Vs, MT, Ma, Mw, and Ms. Volume should be expressed in the unit of m' and mass in grams. Show all calculations to receive full credits.
Can u solve ?(readable) A soil specimen is 38 mm in diameter and 76 mm long, and in its natural conditionweighs 168.0 g. When dried completely in an oven, the specimen weighs 130.5 g. The value ofGs is 2.73. What is the degree of saturation of the specimen?
The laboratory test on a soil sample yields the following results: natural moisture content = 18%, liquid limit = 60%, plastic limit = 25%, percentage of clay sized fraction = 25%. The liquidity index and activity (as per the expression proposed by skempton) of the soil, respectively, are A -0.2 and 1.4 B 0.2 and 1.4 C -1.2 and 0.714 с D 1.2 and 0.714
QUESTION 1 1. For a soil with De=0.41 mm, D = 0.22mm, and Die = 0.08 mm, calculate the uniformity coefficient and the coefficient of gradation. 2. The following are the results of a sieve and hydrometer analysis. Sieve number/ grain size Analysis Sieve Hydrometer 40 80 170 200 0.04 mm 0.015 mm 0.008 mm 0.004 mm 0.002 mm Draw the grain-size distribution curve. Percent finer 100 97 74 27 11 a) b) Determine the percentages of gravel, sand, silt and clay according to the AASHTO system.
1- For a soil, suppose that Dio = 0.08 mm, D3o = 0.22 mm, and Dso = 0.41 mm. Calculate the uniformity coefficient and the coefficient of gradation. 2- The following are the results of a sieve analysis: U.S. sieve no. Mass of soil retained (g) 4 10 18.5 20 53.2 40 90.5 60 81.8 100 92.2 200 58.5 Pan 26.5 a. Determine the percent finer than each sieve and plot a grain-size distribution curve. b. Determine Dio, D30, and D6o from the grain-size distribution curve. c. Calculate the uniformity coefficient, Cu. d. Calculate the coefficient of gradation, Cc.
A SOIL SAMPLE WAS TAKEN FROM A SITE AND WAS PLACED IN A CUBICAL CONTAINER WITH ONE SIDE EQUAL TO 0.1m. THE NET WEIGHT OF THE SOIL IS FOUND OUT TO BE 2kN. AFTER OVEN DRYING, THE WEIGHT WAS REDUCED TO 53%. WHAT IS THE UNIT WEIGHT OF THE SOIL AFTER DRYING? * Your answer A SATURATED SOIL HAS VOID RATIO EQUAL TO 0.65 AND sg = 2.9. WHAT IS THE SUBMERGED UNIT WEIGHT OF THE SOIL? * Your answer THE WEIGHT OF THE VOIDS OF ON SITE SOIL WAS MEASURED AND FOUND OUT TO BE 1 kN. AFTER DRYING, THE WEIGHT OF THE SOLID WAS FOUND TO BE 1 kN. IF THE VOLUME OF THE SOIL IS 0.099 m3, WHAT IS THE NATURAL UNIT WEIGHT OF THE SOIL? * Your answer
Laboratory test results for a sample of clay soil for the purpose of evaluating the potential for volume change (swelling, expansion) are as shown. Rate the volume change potential (high, medium, low) for this soil. LL = 68% PL = 24% Particles smaller than 0.002 mm = 45%
Hydrometer and sieve analysis were conducted on a soil sample. Find D10 Deo uniformity coefficient (Cu), coefficient of curvature (CC) considering the chart given below. Hint: Cu=Deo/D10 and CC=(D3)2 / (D1oxD6o) 100 90 80 70 60 50 40 30 20 10 0,001 CLAY 0,01 SILT 0,1 SAND GRAVEL 10 100 DANE ÇAPI/ PARTICLE SIZE (mm) Dec: (in mm) seç. CC Seç. Cu Seç. D10: (in mm) Seç. GEÇEN DANE YÜZDESİ / PERCENT FINER THAN D