Forces of 25 lb are applied to the handles of the pipe Determine the force exerted on pliers shown in Fig. the pipe at D and the force exerted on handle DAB by the pin at A. 38° 1.25 in. -9 in. 25 lb B C 125 lb

Forces of 25 lb are applied to the handles of the pipe Determine the force exerted on pliers shown in Fig. the pipe at D and the force exerted on handle DAB by the pin at A. 38° 1.25 in. -9 in. 25 lb B C 125 lb

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.1P: A person weighs 30 lb on the moon, where g=5.32ft/s2. Determine (a) the mass of the person; and (b)...

See similar textbooks

Related questions

Q: I can't find C or D

A: Draw the free-body diagram.

Q: 6 m 1.5 m mi -2 mL D 3m. 2.5 m ROUND OFF TO TWO DECIMAL PLACES. The balloon shown in the figure is…

Q: A bent pipe is connected by a thrust bearing and a cable as shown. If a Force, F = 184 lb, is…

A: There will be two reactions at thrust bearing and tension in the cable. Since Force F acts in single…

Q: 8. A 20 kg droid rests on 5.0 m long shelf supported by two cables as shown. The mass of the shelf…

Q: The portable floor crane in the automotive shop is lifting a 530-lb engine. For the position shown…

A: Find force at support C and pressure in piston Load =530 lb

Q: Forces of 5 Nare applied to the handles of the pa- Determine the force exerted per punch shown in…

A: Consider the free body diagram of the single lever as shown below. Here,

Q: Determine the horizontal and vertical components of force which the pin at B exerts on member BC of…

A: The free body diagram of the beam is as follows:

Q: Determine the magnitude of the vertical force Cy for the simply supported beam, where w = 5 kips/ft,…

Q: From the given trusses below, determine the force in the member FG. (kN) Note: Use two (2) decimal…

A: Given data as per question Force applied at c = 12 KN, 4 KN Force applied at D =24 KN, 8KN Force…

Q: Determine all forces acting on member ACD of the The diameter of the pulley at D frame shown in Fig.…

A: Given data Weight of the body W = 500lb To determine the forces acting at ACD in the frame

Q: Q1: Determine the magnitude of the force on the pin at A for the boom shown in Fig. 1. Neglect the…

Q: ! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

Q: The force P on the handle of the positioning lever produces a vertical compression of 56 lb in the…

A: Given that , a=3.4 in b=8.6 in

Q: 20 kg 75 kg 30° 60° Two cylinders having 75 kg and 20 kg mass are connected with a cable and held in…

A: Solution:

Q: Q1: The machine part of negligible weight is supported by a pin at A and a roller at C as shown in…

Q: 3m 3m D 3m 9m 9m / 9m 3m A 9m- 10 kN 10 kN 1. For the truss shown, Determine the Bar Forces AB, BD,…

A: finding ∠DOB, cos∠DOB= 10.5/12 solving we get ∠DOB = 28.95° △OBD is an isoceles triangle, ∠OBD=∠ODB=…

Q: A bag of laundry resting on a chair shown in (a) applies forces on the chair as shown in (b) where…

A: Given data as per the question R =25 N

Q: 2. A block is resting on an incline of slope 5:12 as shown in Fig. It is subjected to a force F =…

A: Given Force, F = 500 N Find Components of F

Q: A bag of laundry resting on a chair shown in (a) applies forces on the chair as shown in (b) where…

A: the reaction at G and the 26 N forces are internal forces and will not be included in the FBD

Q: The 20 × 20-in. square plate shown weighs 56 lb and is supported by three vertical wires. Determine…

A: Given data To determine the weight and location of the lightest block that should be placed on the…

Q: PROBLEM 3: Determine the tension in each of the three ropes supporting the crate. 2 ft 4 ft 4 ft B y…

Q: Three cables are joined at the junction ring C. Determine the tensions in cables AC and BC caused by…

Q: abeling all of the physical quantities given in the problem. Identify your system in the sketch.…

Q: Q3) A lug wrench is used to tighten a square-head bolt. If 50-lb forces are applied to the wrench as…

A: Q3. Draw front view of wrench

Q: Q3) A lug wrench is used to tighten a square-head bolt. If 50-lb forces are applied to the wrench as…

Q: Cords are looped around a small spacer separating two cylinder each weighing 400kn and pass over a…

Q: In the equilibrium position shown, the resultant of the three forces acting on the bell crank passes…

A: To solve this problem, we need to first resolve the force P in horizontal and vertical direction.…

Q: A 39-ft length of railroad rail of weight 44 lb/ft is lifted by the tongs shown. Determine the…

A: Given Length of rail road = 39 ft Weight 44lb/ft is lifted by the tings To find Force exerted at D…

Q: The crate, of weight "W", shown is suspended using the ropes AB and AC The tension in rope AB is 10…

A: Given data Tension in rope AB is 10KN Angle making by rope AC with horizontal is 600 To Determine…

Q: 550 QUESTION 3 100 The figure shows a 180 kg adjustable platfom AB used to raise a 550 kg crate with…

Q: A crate is nung by ropes attached to a steel ring. Assume that the center of gravity (CG) of the…

Q: Q.1) Draw Free-Body diagrams of each of the three cylinders shown below. Each of the cylinders has a…

A: For the given arrangement Weight of cylinder (W) = 400 lb The radius of the cylinder (R) = 15…

Q: The pulley system below is in static equilibrium, where load W3 is 730 N, angle α = 50O and angle θ…

A: Given Data The given load is:W3=730 N θ=30° α=50° To find: The ratio of the load W1W2 Now draw the…

Q: A 600-lb horizontal force is applied to pin A of the frame shown. Determine the forces acting on the…

A: ∑Fy=0Fy-Ey=0........1∑Fx=0 Fx-Ex+600=0...........2 ∑ME=0 Fy(6)-600(10)=0 Fy=1000 lb Putting value…

Q: 1. Determine the force in each member of the truss. State if the members are in tension or…

Q: Q2 Draw the F.B.D for the bar AB and find the reaction forces in A and B If the weight of the bar is…

A: For the given system mass of bar is 40 kg The length of AB is 2 m θ = 30o with ground To…

Q: A log weighing 800 lb is lifted by a pair of tongs as shown. Determine the forces exerted at E and F…

A: Let us draw the FBD of AB Due to symmetry Ay = By = 400 lb And Ax = Bx =65(400lb)=480 lb

Q: A frame and loading are shown. B 90 mm D 120 mm ' 120 mm' 120 mm Determine the force acting on…

Q: d) system of chains Write the solution here: Determine the maximum weight of the engine that can be…

A: Given data: The tension in the cable AB, FAB = 450 lb. The tension in the cable AC, FAC = 480 lb.…

Q: A 24-lb force is required to operate the foot pedal. Determine the tension, 'T' in the connecting…

A: Given data: FA=20 lbC=2 inB=3 in Need to determine the tension (T).

Q: View Policies Current Attempt in Progress A force F of magnitude 810 lb is applied to point C of the…

Q: "STATICS" HOME WORK (2) Q1: The machine part of negligible weight is supported by a pin at A and a…

A: Find the reactions at point A and C.

Q: 1. Determine the force in each member of the truss. State if the members are in tension or…

Q: 1. A museum of modern art is displaying an irregular 426-N sculpture by hanging it from two thin…

A: Given W=426N

Q: 1) Use the method of members to determine the true magnitude and direction of the forces in each of…

Q: A 39-ft length of railroad rail of weight 44 lb/ft is lifted by the tongs shown. Determine the…

A: Given data: The length of the railroad is l=39 ft. The weight of the railroad is w=44 lbft

Q: Determine the axial force in members of the truss system below a. Axial force on member marked with…

Q: Determine the forces in members DE, DI, and JI of the arched roof truss shown below. 46 6 446→6→4>…

A: The free-body diagram of the roof truss is given as, Apply the force equilibrium in the horizontal…

Q: اكتب هنا FREE-BODY DIAGRAM EXERCISES 3/A In each of the five following examples, the body to be…

A: Since you have asked a question with multiple parts in a single request, we would be answering only…

Q: A pole is braced by a guy wire that exerts a force of 250-lb pull on the top of the pole, as shown.…

Question

Forces of 25 lb are applied to the handles of the pipe
Determine the force exerted on
pliers shown in Fig.
the pipe at D and the force exerted on handle DAB by the
pin at A.
38°
1.25 in.
-9 in.
25 lb
B
C
125 lb

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

The end of a water hose weighing 0.5 lb/ft is pulled with a 40-lb force that is inclined at 14 to the horizontal. Determine the length s of the hose that is lifted off the ground and the corresponding horizontal distance L.
A person weighs 30 lb on the moon, where g=5.32ft/s2. Determine (a) the mass of the person; and (b) the weight of the person on earth.
Two 12-kg spheres are placed 400 mm apart. Express the gravitational attraction acting between the spheres as a percentage of their weights on earth.
In the figure shown, the large piston on the left has a diameter of D1 = 9.00 cm.The small piston on the right has a diameter of D2 = 4.00 cm.A lever arm pivot is located a = 5.00 cm to the left of the small piston.A small cylinder hangs from the end of the lever arm a distance b = 25.0 cm to the right of the small piston.In the absence of friction, determine the weight of the cylinder on top of the large left piston which can be supported in equilibrium with the small mass (m = 0.350 kg)hanging from the far right lever arm.Provide a force vector diagram (free body diagram).
A 15 kg block of wood displaces 6 kg of water when submerged in water. Bobuoyant force acting on the block of wood is?( use g =9.8m/s^2) A. 147N B. 58.8 pounds C. 58.8N D. 147 pounds
In a hydraulic press the large piston has a cross sectional area A1=200 sq. cm and the small piston has a cross sectional area A2=5 sq. cm. If the force is 250 N to the small piston. Compute the force acting on the large piston. a. 10 kN b. 12 kN c. 21 kN d. 20 kN
In checking a recently installed fencepost for adequacy of the ground support, a person exerts a force P= -160i +40j +60k N on top of the post. Determine the angles which P makes with the positive x-axis and with the x-z plane.
A man on the wire singing "Man on a Wire" while practicing for his circus show has reached the center of the rope, creating a dip on the center angled at 63.2 degrees. If the mass of the man is 49.55 kg and the tension force that can be handled by the wire is 449.77N, would the wire break? Show the tension caused by the man hanging on the wire.
A heavy crate rests on an inclined surface. Find the smallest force P required to keep the crate from sliding back down the inclined surface, given:Mcrate = 170 kg, μ = 0.2 θ = 20 °
Consider the weights of the two children sitting at ends A and B of a seesaw equal to 40 kg and 30 kg, respectively. Choices: 1.080 m to the right of C 0.720 m to the right of C 1.080 m to the left of C 0.720 m to the left of C
First image: How to determine the tension in the cable and the normal force on thesmooth inclined surface given that W = 100 lb?Second image: How to determine the tension when (gravity) g = 9.81 m/s2?
The pressure of air in the air receiver is 1035 kPa and has a 4450 N force. Determine the piston diameter that can support this force. a. 7. 39 cm b. 10.52 cm c. 11.92 cm d. 9.34 cm