forming condition. 11) Most sheet metal working operations are performed as 12) One of the factors that increase's spring back is 13) Friction and tool wear is more pronounced (occurs clearly) in 14) In roll piercing, the production of seamless tubes is done by 15) In flat rolling, spreading tends to be pronounced (occur clearly) with a work piece of 16) Earing is a type of defect, usually found in forming process. forming process forming condition. width to thickness ratio.

forming condition. 11) Most sheet metal working operations are performed as 12) One of the factors that increase's spring back is 13) Friction and tool wear is more pronounced (occurs clearly) in 14) In roll piercing, the production of seamless tubes is done by 15) In flat rolling, spreading tends to be pronounced (occur clearly) with a work piece of 16) Earing is a type of defect, usually found in forming process. forming process forming condition. width to thickness ratio.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a) Define specific energy for plane strain machining (cutting). b) In plane-strain orthogonal machining, the two main sources of energy dissipation are deformation along the shear plane (~70%) and friction at the tool-chip contact along the rake face (~30%). Consider plane-strain machining of a rigid perfectly-plastic work material whose uniaxial yield stress is 700 MPa, and is independent of strain rate and temperature. A tool of zero-degree rake angle is employed. Measurements showed the (deformed) chip thickness to be twice that of the undeformed chip thickness. Based on the aforementioned distribution of energy, estimate the specific energy for this process.
An automated blanking and forming line is designed to from 2 mm thick sheet, made from 2024 Aluminum, T4 temper, into a square sheet metal part. Elongation at 50mm 20% Young’s Modulus 70GPa Yield strength 325 MPa UTS 470 A) What is the force required to punch a square piece that is 500 mm on each edge? B) If the sheet blank was bent to a radius of 5 mm, what will be the radius after springback occurs? C) What is the required bend angle to achieve a 90° final bend angel for a bend radius of 5 mm?
The figure below shows a symmetric plane-strain upsetting process. The process may also be thought of as a form of side extrusion. Observations show that the deformation is confined to two shear planes, each one being analogous to that seen in plane-strain cutting. You may assume that there is no friction between the work material and the tool/die walls; the uniaxial yield strength of the material is σy and is independent of strain rate and temperature, and the material behaves as a rigid plastic solid. a) Calculate the pressure (p) required for the upsetting process in terms of σy. b) If friction existed at the die walls and the frictional work (energy) dissipation was 30% of the energy required for shape change alone (part (a) above), then what would be the pressure (p)?
1. What process is flexible and is widely used for bending plates for applications such as boilers, cylindrical pressure vessels and various curved structural members? 2. Final velocity of strip in rolling is greater than its initial velocity? True or false?
Question: 2 a. Distinguish between roll bending and roll forming.b. What are some of the simple measures used to assess the feasibility of a proposed cup drawingoperation?c. Compare spinning over the press work for sheet metal products.d. Identify a major technical problem in tube bending.
Question 1 solid cylindrical work piece is reduced in height by an open die forging process using flat dies on a mechanical press, powered by a 20 kW motor which operates at 35 strokes per minute with a stroke length of 160 mm. The work piece is 60 mm high and 100 mm in diameter and is to be reduced in height by 15%. The coefficient of friction during the operation is 0,18. Calculate the flow stress of work piece material if the press is set to operate at 90% of its maximum capacity.
Board Exam April 1997. Two parallel shafts connected by pure rolling turn in the same direction having a speed ratio of 2.75. What is the distance of the two shafts if the smaller cylinder is 22 cm in diameter?
Prepare a comparative table indicating at least 3 characteristics that distinguish volumetric deformation processes from sheet metal working.
1. Derive an expression for the reduction r in drawing as a function of drawing ratio DR.2. A cup is to be drawn in a deep drawing operation. The height of the cup is 75 mm and its insidediameter = 100 mm. The sheet-metal thickness = 2 mm. If the blank diameter = 225 mm, determine(a) drawing ratio, (b) reduction, and (c) thickness-to-diameter ratio. (d) Does the operation seem feasible?3. A drawing operation is used to form a cylindrical cup with inside diameter = 65 mm and height =50mm. The starting blank size = 140 mm and the stock thickness = 2.8mm. determine (a) drawing forceand (b) holding force, given that the tensile strength of the sheet metal (low-carbon steel) = 350 MPa andyield strength = 190 MPa. The die corner radius = 6 mm. Based on these data, is the operation feasible?
the work metal has a flow curve defined by K=300MPa and n=0.2, and the coefficient of friction between the rolls and the work is assumed to be 0.1. a 250mm wide strip 2.0cm thick is fed through a rolling mill with two powered rolls each of radius=300mm. the work thickness is to be reduced to 18mm in one pass at a roll speed of 50rev/min. what will be the power for this operation?
Forging procedures may be classified in part by how much room there is for movement in the die. Please identify the three primary classes that this system generates.
In rolling process 40mm thick plate is rolled to 20mm in two high rolling mills. Roll diameter is 200mm the angle of contact is 15degree. Determine no of roll passes required to obtain final desires thickness