Four forces (including the weight of the cylinder) are applied to a ring at point A as shown. Knowing that the system is in equilibrium, determine the magnitude and direction of the unknown force I Note: The actual direction of I may be different from that shown in the diagram. 750 ib 150 ib The weight of the cylinder (a vertical force) is 1000 lb.

Four forces (including the weight of the cylinder) are applied to a ring at point A as shown. Knowing that the system is in equilibrium, determine the magnitude and direction of the unknown force I Note: The actual direction of I may be different from that shown in the diagram. 750 ib 150 ib The weight of the cylinder (a vertical force) is 1000 lb.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer is 1,022.80. Show your solution. Forces F1 and F2 shown below act on the screw eye. If F1 = 501 lb, determine the magnitude of the resultant force (in lb) if it is directed vertically upward. Use F2 = 578 lb., α = 20°.
Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the 1m x 5m gate shown in the figure. Pressure of air = 32 kPa Fluids: fluid a (s=3.93) fluid b (s=0.23) fluid c (s=1.19) h1= 0.7 m h2= 1.6 m h3= 3.7 m Round your answer to 3 decimal places.
As shown in this image, water fills a tank with a sloped side, which has a flat, rectangular gate of height 6-ft and width 7-ft. The hinge along the top allows the gate to open when a force P is applied. If you neglect friction and the weight of the gate, what is force, P, in lb-f required to open the gate?
The cylinder in the figure below, having a mass of 100 kg is to besupported by the cord that wraps over the pipe. Determine the largest vertical force F that can be applied to the cord without moving the cylinder. The cord passes two times over the pipe (take β = 540° and μS = 0.3).
In the figure shown, each block has a mass of 2-kg.Determine the force P needed to start block B to theleft. The angle of friction for all surfaces in contact is16.7 degrees.
Problem 9. For the tank shown in the figure, the following dimensions apply: h1=3.00m h2=4.50m w=2.50m y=9.81kN/m^3. Compute the horizontal component of the resultant force on the curved surfaces.a. 168.0 kNb. 158.0 kNc. 148.0 kNd. 138.0 kNe. 128.0 kNf. 118.0 kN
A basketball player hangs from the hoop when performing a "dunk" by exerting 2 forces of 100 pounds on it at the indicated points. The bounded dimensions are as follows: h = 14.5 in, r = 9.5 in, α = 120 °. If the indicated forces are replaced by another force applied at point O, which will generate the same effect as the original system. Determine the values of the new force and the torque M that is generated.
A weight of 300.0 kg is pulled from the water by the setup consisting of two slanted poles and a moveable rope as shown in the figure below. Take the value of acceleration due to gravity g = 9.8 m/s2. (Round your answer to one decimal place.) (a) Indicate the coordinates of A, B, C and D in m. (b) Find the position vectors along AB, CB, BD in m and corresponding unit vectors. (c) Determine the magnitude of the force in N along the pole AB, CB and BD.
2. Given: X = 100 kg; Y = 150 kg Solve for the acceleration of block X in m/s2 for Case 2. Ignore the friction and mass of pulleys. (3 significant figures)
Compute the resultant of the three forces shown in the figure. a.) None of the Above b.) 315.28 N c.) 836.90 N d.) 894.32 N e.) 948.27 N
Q1(a) Explain the difference between wetting fluid and non-wetting fluid (b) The 60m X 60m rectangular gate shown in Figure Q1(b) has its top edge located 3m vertically below the water surface. The gate is to be opened from its lower edge by applying a normal force by the shaft. Determine the minimum force F required to open the water gate. (Ignore Patm in all your calculations)
Need help experts. The rigid body shown in the figure is subjected to the indicated force system. Determine the forces applied at points A and E that equal the applied force system.Data: β = 48°; a = 6,6 m; b = 8,9 m; F = 31 kN; P1 = 20,743 kN; P2 = 23,037 kN The force applied at point A is FA = ? Answer kN and the force applied at point B is FB = ? Answer kN.