Question 3 The rigid structure BCD is supported as shown. Assume a = 6.7 ft, b = 4.8 ft, c = 3.0 ft, d = 1.8 ft, and e = 30°. Tie rod (1) is attached at A and C with double shear pin connections, while the pin at B is attached with a single shear connection. The pins at A, B, and C each have a diameter of 0.625 in. and an ultimate shear strength of 81 ksi, and tie rod (1) has diameter of 0.875 in. and a yield strength of 43 ksi. Determine the allowable load P that may be applied to the rigid beam if an overall factor of safety of 1.9 is required. (1) В Answer: Pallow = kips

Question 3 The rigid structure BCD is supported as shown. Assume a = 6.7 ft, b = 4.8 ft, c = 3.0 ft, d = 1.8 ft, and e = 30°. Tie rod (1) is attached at A and C with double shear pin connections, while the pin at B is attached with a single shear connection. The pins at A, B, and C each have a diameter of 0.625 in. and an ultimate shear strength of 81 ksi, and tie rod (1) has diameter of 0.875 in. and a yield strength of 43 ksi. Determine the allowable load P that may be applied to the rigid beam if an overall factor of safety of 1.9 is required. (1) В Answer: Pallow = kips

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Take 2 KN/m in place of 1.5. Determine support reaction
For the truss shown below, applied loads are PB = 73 kN, PC = 36 kN and PD = 15 kN. Using the sign convention 'tension positive', select the correct answer for the axial force in member GH in kN: К F AR G В Рв 4@3m=12m O 1. The axial force in member GH is -60 kN. O2. The axial force in member GH is -78 kN. O 3. The axial force in member GH is -67.1 kN. Н Pc J D Ро K E 4m ?
From the given truss shown, compute the force in member DE. a.62.5 N (C) b.187.5 N (C) c.62.5 N (T) d.37.5 N (C)
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given structure with P = 15.5 kN. Determine the force in member CD, DG, CF, BC, EF, BF, BE, AB, AE, and FG of the truss shown. State whether each member is in tension (T)or compression (C).
Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places Structural Theory a. Determine the vertical reaction R₂ in KN. b. Determine the shear at midspan between vertical supports in KN c. Determine the maximum factored load moment in the beam in KN.m
A simple wooden AB beam (see figure 2) supportsa uniform load of 24 kN / m (includes weightcharacteristic of the beam), with a length L = 1.75m and sectionrectangular cross section with width of 200mm and height250mm. Determine:a) Reactions and shear diagram.b) Using the maximum shear force, find theshear stress in:to. The centroid.b. At a distance of 62.5mm from the centroid.c. At the ends of the cross section.c) Draw the shear stress diagram withall values obtained.
The wooden members in the simple truss below have the following capacity: Shear parallel to grain = 1 MPa, Compression parallel to Grain = 11MPa, Compression perpendicular to Grain = 5 MPa 1. Find the minimum safe x. a. 73 mm b. 160 mm c. 148 mm d. 112 mm 2. Find the minimum safe y. a. 15.97 mm b. 19.45 mm c. 9.14 mm d. 18.28 mm 3. Determine the stress in member AC. a. 1.13 MPa b. 1.258 MPa c. 1.224 MPa d. 1.04 MPa
If the allowable bearing stress for the material under the supports at A and B (σ_(b allow)= 1.5 MPa, determine the size of square bearing plates A’ and B’ required to support the load. Dimension the plates to the nearest mm. The reaction at the supports are vertical. Take P = 100 kN.
Two d mm*10 mm cover plates are welded to two UPN 200 channels 100 mm high to form the cross section of the compound beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 19.10*106 mm4. a) Determine the support reactions. b) Draw the shear force and bending moment diagrams. c) If the allowable bending stress of the beam is 300 MPa, find the required width d of the plates to safely support the load.
Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places. Please answer all since they are all subquestions. Thanks Structural Theory 1d. Determine the vertical reaction R₂ in kN 1e. Determine the shear at midspan between vertical supports in kN. 1f. Determine the maximum factored load moment in the beam in kN.m
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 980 mm2. Assume a = 2.1 m, b = 7.6 m, and c = 3.8 m. If P = 40 kN and Q = 80 kN, determine the normal stress in each member
Determine the area of the moment diagram of the structure Choices: (-PL^2)/2 (2PL^2)/3 (-2PL^2)/3 (PL^2)/2