Four metal rods with equal cross-sectional areas were subjected to a tensile test. Given Young's Modulus values of the metal samples, determine which metal will have the HIGHEST stress when it undergoes elongation to 0.1. Material Young's Modulus (GPa) 70 ... Aluminum Сopper Steel 110 200 Lead 1.6 A lead B) steel (c) aluminum D) copper

Four metal rods with equal cross-sectional areas were subjected to a tensile test. Given Young's Modulus values of the metal samples, determine which metal will have the HIGHEST stress when it undergoes elongation to 0.1. Material Young's Modulus (GPa) 70 ... Aluminum Сopper Steel 110 200 Lead 1.6 A lead B) steel (c) aluminum D) copper

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 57PQ: A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length...

See similar textbooks

Similar questions

Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
Discuss how you might measure the bulk modulus of a liquid.
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
Can Young’s modulus have a negative value? What about the bulk modulus?
Bone has a Youngs modulus of 18 109 Pa. Under compression, it can will island a stress or about 160 106 Pa before breaking. Assume that a femur (thigh bone) is 0.50 m long, and calculate the amount of compression this bone can withstand before breaking.
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
Review the relationship between stress and strain. Can you find any similarities between the two quantities?
Review. A wire of length L, Youngs modulus Y, and cross-sectional area A is stretched elastically by an amount L. By Hookes law, the restoring force is kL. (a) Show that k = YA/L. (b) Show that the work done in stretching the wire by an amount L is W=12YA(L)2/L.
A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57
A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear deformation, taking it to have the shear modulus of 1109 N /m2. The disk is equivalent to a solid cylinder 0.700 cm high and 4.00 cm in diameter.
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?