Four resistances having value 'R' are connected in parallel combination. Which ofthe following statement is true for the circuit.the equivalent resistance can never be greater than REvery resistance will have the different amount of current flowing through itthe equivalent resistance will always be greater than RVoltage drop across the resistances will vary as per the value of R.

Four resistances having value 'R' are connected in parallel combination. Which of the following statement is true for the circuit. the equivalent resistance can never be greater than R O Every resistance will have the different amount of current flowing through it the equivalent resistance will always be greater than R O Voltage drop across the resistances will vary as per the value of R.

Four resistances having value 'R' are connected in parallel combination. Which of the following statement is true for the circuit. the equivalent resistance can never be greater than R O Every resistance will have the different amount of current flowing through it the equivalent resistance will always be greater than R O Voltage drop across the resistances will vary as per the value of R.

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter21: Circuits And Dc Instruments

Section: Chapter Questions

Problem 11PE: Show that if two resistors R1and R2are combined and one is much greater than the other (R 1 >>R 2 ):...

See similar textbooks

Similar questions

A short circuit in a 120-V appliance cord has a0.500- resistance. Calculate the temperature rise of the2.00 g of surrounding materials, assuming their specific heat capacity is 0.200cal/gC and that it takes 0.0500 sfor a circuit breaker to interrupt the current. Is this likely to be damaging?
Show that if two resistors R1and R2are combined and one is much greater than the other (R 1 >>R 2 ): (a) Their series resistance is very nearly equal to the greater resistance R 1. (b) Their parallel resistance is very nearly equal to smaller resistance R2.
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
Use the atomic theory of matter to explain why the resistance of a material should increase as its temperature increases.
Consider the circuit below. The battery has an emf of = 30.00 V and an internal resistance of r = 1,00 . (a) Find the equivalent resistance of the circuit and the current out of the battery. (b) Find the current through each resistor, (c) Find die potential drop across each resistor, (d) Find the power dissipated by each resistor, (e) Find the total power supplied by the batteries.
Does the resistance of an object depend on the path current takes through it? Consider, for example, a rectangular bar-is its resistance the same along its length as across its width? (See Figure 20.37.)
Three identical 60.0-W, 120-V lightbulbs are connected across a 120-V power source as shown in Figure P28.72. Assuming the resistance of each lightbulb is constant (even though in reality the resistance might increase markedly with current), find (a) the total power supplied by the power source and (b) the potential difference across each lightbulb.
The ignition circuit of an automobile is powered by a 12-V battery. How are we able generate large voltages with this power source?
The severity of a shock depends on die magnitude of the current through your body. Would you prefer to be in series or in parallel with a resistance, such as the heating element of a toaster, if you were shocked by it? Explain.
(a) What advantage does 120-V operation offer over 240 V? (b) What disadvantages does it have?
Check Your Understanding When using Kirchhoff’s laws, you need to decide which loops to use and the direction of current flow through each loop. In analyzing the circuit in Example 10.7, the direction of current flow was chosen to be clockwise, from point a to point b. How would the results change if the direction of the current was chosen to be counterclockwise, from point b to point a?
An office worker uses an immersion heater to warm 250 g of water in a light, covered, insulated cup from 20.C to 100. C in 4.00 minutes. The heater is a Nichrome resistance wire connected to a 120-V power supply. Assume the wire is at 100. C throughout the 4.00-min time interval. (a) Calculate the average power required to warm the water to 100. C in 4.00 min. (b) Calculate the required resistance in the heating element at 100. C. (c) Calculate the resistance of the heating element at 20. C. (d) Derive a relationship between the diameter of the wire, the resistivity at 20. C, 0, the resistance at 20. C, R0, and the length L. (e) If L = 3.00 m, what is the diameter of the wire?