From its below response to a unit step input, find the damping ratio(), undamped natural frequency (@,), da mped natural frequency(@),peak time (t,), rise time (t,), and steady state value (y,,) if the input is aunit step.0 تمت الاجابة على السؤال وساقوم برفع الاجابة في نهاية الأسظلة1.4120.80.60.40.210Time (s)

Answered: Image /qna-images/answer/84d66fc4-da6d-4433-82b8-04baa29fd2a8.jpg

From its below response to a unit step input, find the damping ratio (5), undamped natural frequency (o,), damped natural frequency(o), peak time (t,), rise time (t,), and steady state value (y) if the input is a unit step. 0 دمت الاجابة على السؤال وساقوم برفع الاجابة في لهاية الأسئلة 1.4 1.2 0.8 0.6 0.4 10 Time (s)

From its below response to a unit step input, find the damping ratio (5), undamped natural frequency (o,), damped natural frequency(o), peak time (t,), rise time (t,), and steady state value (y) if the input is a unit step. 0 دمت الاجابة على السؤال وساقوم برفع الاجابة في لهاية الأسئلة 1.4 1.2 0.8 0.6 0.4 10 Time (s)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assume that the signal to be measured is displayed in the following form. y(t)=5sin1000t mV The time constant of the 1st order device is 100ms, K=1 V/V and its output is transferred to the 2nd order amplifier. The natural frequency and damping ratio of the amplifier is 15,000Hz and 0.8, respectively. Then, determine the expected output signal of y(t). And calculate the dynamic error and phase delay on the output. Is the chosen metrology system reasonable? If not, suggest a way.
100 y(t)+ y (t) = X(t) for a system defined by a first-order differential equation:a. Draw the log magnitude(dB)-log frequency graph of H (jw) (phase graph is not requested. it is expected that the frequency axis will also be logarithmic when plotting the log magnitude graph).b. If the magnitude of H(jw) is -40 dB, it is assumed that the input is suppressed. it is given that the signal X (t) = coswat is suppressed by this system. What is the smallest wa value in this case?
A forced excited m–k–c system is under a harmonic force F: F=5000sinωt If the mass m = 50 kg; k=80E3 N/m; damping ratio=0.3 and dynamic deflection is to be less than 0.08 m. Determine the range of operating excitation frequency. Also the show the operating range of frequency on a graph.
A continuous time signal, x(t) = sin(20πt) + cos(40πt), is sampled uniformly at intervals of T to obtaina discrete time signal,x(n) = sin(πn/5) + cos(2πn/5).a) What is the value of T assuming no aliasing has occurred?b) Assume both frequency components have been aliased. In this case, is your choice of T unique? If not,specify some choices of T consistent with the information given
a) Calculate the range of values K will take for the steady-state error to be “??? ≤ 0.04” when the input of the system is ?(?) = ?. b) Calculate the value range that K will take so that the damping ratio can be “1 > ξ ≥ 1 2√6”. c) Calculate the damping ratio “ξ” and the undamped natural frequency ?? value so that “? = 0.5”.
For the system defined by the first-order differential equation 100y'(t) + y(t) = x(t). a) Plot the log magnitude (dB)-log frequency graph of H(jw). b) The input is assumed to be suppressed when the magnitude of H(jw) is -40 dB. It is given that the x(t)=coswat signal is suppressed by this system. What is the smallest wa value in this case? Subject: Signals and Systems
In case the sound from the engine of a vehicle is modelled by the function y(t) = cos[ω(t + τ) + θ] where time delay=τ & phase=θ Determine the frequency & period of the signal u(t) whena)[ω, τ, θ] = [π/3, 1/2, π/2]b)[ω, τ, θ] = [3π/4, 1/2, π/4] N.b time should be in seconds & frequency in Hertz. c) y(t) = e-atu(t) for t≥0 & y(t) = 0 for t<0 where a>0 is a constant The function above defines the model of the decay of the vibration of a vehicle engine. i.Make a sketch of the signal y(t) & determime its fourier transform.
Difference equation of a discrete-time causal (right-sided) LTI system, y(n) = 2 x(n) – x(n-1) -1/4 y(n-1) + 1/8 y(n-2) is given as. a) Give the system function H(z). b) Indicate zero, poles and ROC in the Z-plane. Is the system stable? Please explain. c) Find the impulse response of the system. d) If the system is left-sided, repeat (b) and (c).
At t=0, a 1 pound force, denoted by f(t), is applied to the translational mechanical system. Determine K and M such that the response has a 1 second peak time and 4 second settling time if fv = 1. Additionally, what is the resulting overshoot percentage? Determine also the resulting transfer function as well as the steady state error for step input.
Consider the discrete-time dynamical system xt+1=0.48xt + 2. What is the equilibrium for this system______? What is the updating function rule f(x) _____? What is the derivative of the updating function_______? Is the equilibrium stable, unstable, or neither_______?
The system function of a discrete-time causal LTI system is H(z) = z / (z2 +1.5 z -1) a) Show the poles/zeros and the ROC in the Z-plane. Is this system stable? Explain. b) Calculate the impulse response h(n). c) Give the difference equation of this system. d) Repeat questions (a), (b), (c) if this system is changed to be stable.
: If F(s) = s 4+ 5s3+20s 2 + 40s + 50 , Investigate the stability of this system