(g) Which of following values corresponds to the static power dissipation, Ps, of the MOSFET in the circuit shown in Figure 1.7 when Rp = 160 N, Vs= 10 V and vIN = 4 V? Assume that the MOSFET is operating in saturation and the drain-source current is given by the usual expression shown below where Vr=1 V and K = 1 mA/V?. K ips(sat) (Vos -V,) GS S D VIN RD Vo -Vs +. Vs Figure 1.7 (B) Ps=425 mW (A) Ps= 175 mW (D) Ps= 200 mW (C) Ps=250 mW +

(g) Which of following values corresponds to the static power dissipation, Ps, of the MOSFET in the circuit shown in Figure 1.7 when Rp = 160 N, Vs= 10 V and vIN = 4 V? Assume that the MOSFET is operating in saturation and the drain-source current is given by the usual expression shown below where Vr=1 V and K = 1 mA/V?. K ips(sat) (Vos -V,) GS S D VIN RD Vo -Vs +. Vs Figure 1.7 (B) Ps=425 mW (A) Ps= 175 mW (D) Ps= 200 mW (C) Ps=250 mW +

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ı just need fınal answer Considering the dc operating conditions of the NMOS circuit in the figure, gm = 1.5 mS was obtained. Also, the load current IL flowing through RL when Rsig1 = 2 kΩ, Rsig2 = 3 kΩ, RF = 60 kΩ, R1 = 50 MΩ, R2 = 12 MΩ, RD = 4.7 kΩ, RS = 1.2 kΩ and RL = 13.3 kΩ What would be the value of ? (Vi1 = 20 mV, Vi2 = 30 mV) NOTE-1: Capacitors are negligible at mid-band frequency. NOTE-2: The NMOS output impedance will be taken into account and its value is rd = 20 kΩ. a. 0,28 mA b. 0,20 mA c. 0,84 mA d. 0,40 mA e. 0,52 mA f. 0,72 mA g. 0,60 mA h. 0,12 mA
In the Boost DA-DA circuit:Source voltage (E) value: in the range of [17-29] (volts),Switching frequency (f) value: 20 khz,Voltage between load ends: 40VCapacitance value: 470uFPower dissipated at load: 10 watts What is the lowest inductance L, in uH, that can keep the DC-DC converter in continuous current under these conditions? a) 269.3731 b) 415.4375 c) 364.8204 d) 163.6472 e) 578.1875
For the transistor , IS = 4 × 10−16 μA,βF = 75, and βR = 4. (a) Label the collector, base,and emitter terminals of the transistor. (b) What isthe transistor type? (c) Label the emitter-base andcollector-base voltages, and label the normal direction for IE , IC, and IB. (d) Write the simplified formof the transport model equations that apply to thisparticular circuit configuration. Write an expressionfor IE /IB. Write an expression for IE /IC. (e) Findthe values of IE , IC, IB, VC B, and VE B.
circuit shown in the figure, Kn = 2mA / V2, VIN = 0.7V for Mi mosfeti. So, what kind of relationship should there be between R1 and R2 resistance for mosfet to work at saturation?
Considering the dc operating conditions of the NMOS circuit in the figure, gm = 1.9 mS was obtained. Also, the load current I flowing through RL when Rsig1 = 2 k2, Rsig2= 3 kQ2, RF = 60 KQ2, R1 = 50 MS2, R2 = 12 MS2, RD= 4.7 k, RS = 1.2 KQ and RL = 11.3 k What would be the value of ? (Vi1 = 20 mV, Vi2 = 30 mV) NOTE-1: Capacitors are negligible at mid-band frequency. NOTE-2: NMOS output impedance will be considered. and its value is rd = 20 k (Q=ohm) (S2=ohm)
Hey, can you please make sure this question is solved correctly and step by step solution to the way to approach and how it's done please. I want to learn how to do this type of problem. Fig. 1 is a simplified structure of the MOSFET (NMOS) transistor.What are the requirements for MOSFET to operate in:a) triode mode?b) saturation mode?c) cutoff mode?Explain
Present your complete analysis, solution in the proper sequence, and all needed figures. Show all computations.What change(s), if any, can be introduced into the circuit shown below for a) zero bias? b) depletion- mode bias? c) enhancement- mode bias?
‏( b ) For the Junction Field Effect Transistor ( JFET ) shown in Figure Q1 ( b ) below , given that maximum current Ipss = 10 mA , pinch - off voltage Vp = -5 V , R D= 2 ka , source voltage and resistance are VDD= 12 V and Rs = 5 kn , respectively , solve to determine following (i) The quiescent voltage between the gate and source VGSQ . (ii) The quiescent drain current IDQ
Q3:Choose One of the following: : (A)In common emmiter voltage divider bias of BJT, Vcc = 25V; R1= 10 k ohm; R2, = 2.2 k ohm ;Rc = 3.6 k ohm and RE = 1 k ohm.Determain Vec at ß = 120.using Exact analysis Draw the equvelent circuit inaddition the DC load line curve . (B)For self bais(Emitter resistace bais) of BJT,Vcc= 22 V, lb = 45macroA, a = 0.99, RE = 1 k ohm. Determain VCe Draw the equvelent circuit inaddition to DC load line curve.
The switches as shown can be implemented using MOSFETs, as shown. What must be the W/L ratios of the transistors if the onresistance of the transistor is to be less than 1 percent of the resistor 2R = 12 kΩ? Use VREF = 3.0V. Assume that the voltage applied to the gate of the MOSFET is 5Vwhen b1 = 1 and 0Vwhen b1 = 0. For the MOSFET, VTN = 1 V, Kn = 50 μA/V2, 2φF = 0.6 V, and γ = 0.5√V.
For many years, MOS devices were scaled tosmaller and smaller dimensions without changingthe power supply voltage. Suppose that the widthW, length L, and oxide thickness Tox of a MOS transistor are all reduced by a factor of 2. Assume thatVT N , vGS, and vDS remain the same. (a) Calculatethe ratio of the drain current of the scaled device tothat of the original device. (b) By what factor hasthe power dissipation changed? (c) By what factorhas the value of the total gate capacitance changed?(d) By what factor has the circuit delay Tchanged?
Considering the operating conditions of the NMOS circuit in the figure, 9m = 1.9 m was obtained. Also,RL when Rsig1 = 2 ko, Rsig2 = 3 kA, RF = 60 kg, R1 = 50 MQ, R2 = 12 MA, RD = 4.7 ko, RS = 1.2 kq and RL = 11.3 koWhat is the value of the load current li flowing through it? (Vi1 = 20 mV, Vi2 = 30 mV)NOTE-1: Capacitors are negligible at mid-band frequency.NOTE-2: NMOS output impedance will be taken into account and its value is ra = 20 ko.