Generalised coordinates are always measured in relation to the equilibrium position. Choose an option: o True o False

Q: 2. A furnace wall is made up of three layer of thickness 250 mm, 100 mm, and 150 mm with thermal…

A:

Q: The minimum specific energy in a rectangular channel, 3-m wide, is 2 m. What is the discharge, in…

A: At minimum specific energy , depth of flow is critical and maximum discharge occurs..

Q: So first Draw the free body diagram Then second Find the Reactions Lastly Draw the Shear and Moment…

A: Draw the given diagram of the beam.

Q: Water at 10°C is is flowing at 0.8 m/s across a long cylinder that is made of a material that…

A:

Q: During the Rayleigh process if the flow is subsonic, due to heat addition the velocity decreases…

A:

Q: Determine the moment of inertia for this circle about: (a) The x-axis (b) The y-axis (c) Axis, a-b

A:

Q: Determine the Euler Buckling axial compressive load of W 12 x 72 section having a length of L=48 ft…

A: To find: The Euler Buckling load. Given: The length of the column, L = 14.63 m. Young's modulus, E =…

Q: The frame supports the 400-kg load in the manner shown. Neglect the weights of the members compared…

A: To find: Horizontal and vertical components of all the forces acting on each of the members:…

Q: Calculate shear force and bending moment at point c

A:

Q: Given a projectile with a m= 0.025 kg with a velocity of v = 400 m/s which impacts a rod with a mrod…

A:

Q: 2m Z 1.5 kPa R T I'm

A:

Q: A steel beam, of lengths a=5 m and b= 3 m and a hollow box cross section, is supported by a hinge…

A:

Q: 1. Draw the complete shear and bending moment diagrams. A 1 m 600 N 2m 600 N -1 m- B

A:

Q: During the Rayleigh process if the flow is subsonic, due to heating the stagnation pressure…

A: Rayleigh Process: Rayleigh flow refers to frictionless, non-adiabatic flow through a constant area…

Q: A Rankine cycle is executed with steam expanding initially from 20 MPaa and 150 deg SH. Condensation…

A:

Q: 4) The equations below represent the initial and final states of a process (plus some additional…

A: Write the given data.

Q: can please help me understand how someone could possibly do 75 windmills in a minute?? with madeup…

A: It is asked to perfrom basic analysis while performing 75 windmilles in a minute.

Q: An airplane flies at 400 mph at 1600 f altitude on a standard day. The plane climbs to 50,000 ft and…

A:

Q: For the three scenarios shown below, determine the angular velocity about point O, if each rigid…

A:

Q: A uniform cross-section bar is shown in the figure. This bar is set on the wall and subjected to a…

A: For solution refer below images.

Q: This is a follow up to my question and the answer you submitted. The equation you used for J is…

A: According to question:- Outer radius of pipeR=50mm⇒Outer diameterD=2R=100mm=0.1mInner radius of…

Q: Consider the base plate of an 1200 W household iron with a thickness of L= 0.5 cm, base area of…

A:

Q: What is the location of FR, i.e., the distance d? A M 3 m 3 m F. R B

A:

Q: An object with 3.5 lb weight consists of a cylinder and hemisphere of the same material. Determine…

A: Given :  Weight (W)= 3.5 lb ,  Assuming , W1 = Weight of the cylinder                     W2 =…

Q: The system in Figure consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-…

A:

Q: Find the shear force and bending moment at point C. 8 kN A Answer: Vc = -11.8 kN Mc = -35.4 kN - m…

A: For the given configuration of beam, it is required to determine the shear force and bending moment…

Q: Figure 1. Length of line AC? a. 8.33" b. 5.83" c. 9.72" d. 11.33"

A:

Q: Bar AB in the figure rotates counterclockwise with a constant angular velocity of 2.5 rad/s. If all…

A: Write the given data. ωAB=2.5 rad/sρ=2 kg/mAB=0.8 mBC=0.8 mCD=0.4 mθ=60°α=60°

Q: Bar AB in the figure rotates counterclockwise with a constant angular velocity of 2.5 rad/s. If all…

A: Given that ,  constant angular velocity of the bar AB ωAB=2.5rad/s all of the bars have a unit mass…

Q: A horizontal cylindrical rod with a length of 2 m and a diameter of 0.2 m is used for the top of a…

A: Given data h=3.312 W/m2k4L=2 md=0.2 mTs=40°CT∞=30°C Here, h is the convection coefficient and L is…

Q: If the moment of inertia of the thin strip of area about the x-axis is 2.66(106) mm4, determine the…

A:

Q: Consider the function p(x) = 24 - 4x³+3x²+x-1. Use Newton-Raphson's method with initial guess of 3.…

A: Detailed explanation and solution of the above problem uploaded in below pictures.

Q: Draw SFD and BMD considering the load condition on the given beam

A:

Q: 7.37. The sketch depicts a simplified flow situation in a two-dimensional wind- or water-tunnel in…

A: Given: Initial velocity of the fluid: →V1=30.5 m/s Height of the tunnel: →H=1.2 m If we take unit…

Q: Problem mts): Consider incompressible Newtonian fluid flow between parallel plates (Fig. 2) that are…

A: Given: constant pressure gradient 1-D flow with fixed plate at boundaries To find: (a) equation (b)…

Q: A projectile is shot directly away from Earth's surface. Neglect the rotation of the Earth. What…

A:

Q: A shaft with 3 meters span between two bearings carries two masses of 10 kg and 20 kg acting at the…

A:

Q: Locate the centroid y of the beam's cross-sectional area. Step 3: Complete the table Segment T 50 mm…

A: To find: The centroid of the component with respect to the global coordinate and the area-weighted…

Q: Estimate the bending moment stress at the root of a glider's wing spar when it is performing a level…

A: Given: Thickness or depth of the rectangular beam: →y=4 inches Cross sectional area moment of…

Q: *answer is correct To increase the rate of heat transfer from a device, which has 0.1 m² of exposed…

A:

Q: Q.8) Water (u= 1cP) flows through the 20-mm diameter galvanized iron pipe (ε=0.15 mm) such that it…

A: Given data: d=20 mmd=20*10-3 md=0.02 mQ=0.003 m3/sε=0.15 mmKelbows=0.9Kgate valve=0.19

Q: A) Draw the free body diagram BDF. B) Solve for the reactions at B and D. C) Draw the free body…

A:

Q: Three cables are joined at the junction ring C. Determine the tension at AC Three cables are joined…

A:

Q: Find the shear force and bending moment at points C and D. 300 lb/ft A 12 ft 15 ft C B D 3 ft 6 ft…

A:

Q: 3 m L Member AL is a: 20 kN K φ· B -2m--2 C Tensile Member Compressive Member Zero-Force Member Not…

A:

Q: A P3 3 m B F P₁ 3 m E C P₂ 3 m 3 m D

A:

Q: A Two-pass steam Condenser is designed for a full heat load of (293 MW) at a pressure of (0.05 bar).…

A:

Q: 100 mm 200 mm GIVEN: Coefficient of static friction at A = 0.4 Collar at B is smooth and exerts…

A:

Q: A 8.0 m long ladder AB leans against a smooth wall making an angle of 70º with the floor. The ladder…

A: Given:Length of the ladder, l=8 mAngle made with the floor, θ=70°Mass of the ladder, m=40 kg

Q: At the beginning of the compression process of an air-standard Diesel cycle, p₁ = 95 kPa and T₁ =…

A:

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.