Generate a time delay of 20 ms with a 16-bit timer 0. (Crystal frequency 10MHz) When the time is up, call a subroutine. (Do not use interrupts, detect the time is up by polling.) In the subroutine, perform AND operation between the values at 16h and 26h. Save the result to the address that is pointed by the resu (For example, if the result is 20, the value 20 will be written to address 20).

Generate a time delay of 20 ms with a 16-bit timer 0. (Crystal frequency 10MHz) When the time is up, call a subroutine. (Do not use interrupts, detect the time is up by polling.) In the subroutine, perform AND operation between the values at 16h and 26h. Save the result to the address that is pointed by the resu (For example, if the result is 20, the value 20 will be written to address 20).

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

What is an MSDS?
Draw the Moore and Mealy State Diagram of a Finite State Machine thatfunctions as a Binary Sequence Detector for the following sequence:a. 01011b. 101 and/or 010Obtain the State Table for each of your diagrams?
S Display will be designed for a thermometer. The display will show that degree for minimum temperature and 99 degrees for maximum temperature. According to this; a) What is the number of bits that will be needed in the binary code to express the temperature? b) What are the binary, octal and hexadecimal equivalents of 95 degrees? () What is the BCD representation of 95 degrees? d) What is the hex equivalent of this temperature when it shows 111 degrees octal? e) If the thermometer showed a temperature between -99 and +99 degrees, how many bits would we need?
A)What will be the frequency at C if the clock is 320 kHz? B) What is the modulo of the circuit? C) What is the output (in binary) after 737 pulses?
18 initial state of the 10-bit ring counter is given as 1101000000. According to this, which of the following options is correct at the end of the second clock pulse? e) none
Discuss with timing diagram the operation of a 3-bit Asynchronous Counter.
2.Assuming the processor frequency is 20 MHz, find the highest square wave frequency that can be generated using Timer0 in 16-bit mode. (Calculations only, no code needed).
Design a 4-to-1 multiplexer using a 2-to-4 decoder and only AND and OR gates? Briefly explain how your circuit works?
Assess the method to generate a 6.25 MHz signal using a 10-bits serial shift register operated with 50 MHz clock. Show all the necessary steps, delay calculations and workings in your answer.
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
Assume a three-story hospital is built at Expo Center Karachi, and you are hired to design the logic circuit for the newly installed lift. The lift only stops at Ground, Second, Third Floors. The lift has one button (RUN), that can be turned into Up or Down position. When the switch is turned to the UP position (i.e. R=1), the lift goes upward from the Ground floor (i.e. 0) to the top floor (i.e. 3), and if the switch is turned to the DOWN position (i.e. R=0) it will go downward. Design this synchronous sequential circuit for this up-down counter using the JK-flip- flops. Perform all design steps, including state-diagram, state-table, K-map, minimized expressions and finally, the draw the logic circuit.
Explain each component of the block diagram of a frequency counter. - Input: - Accurate time-base / clock: - Decade dividers and flip-flop: - Gate: - Counter/ latch: - Display: