Give me answer  both c and d. I don't want single answer. Thank you  (c) Provide the reasons for ensuring that tension member slenderness cannot exceed 300 (d) Discuss the advantages and disadvantages of punching versus drilling holes in steel construction

Q: What is the optimal thickness of a plate sheet that can be punched out if the design stress is about…

A: Yield stress=design stress/factor of safety                =200/5= 40psi Shear area=πD*t=π*2*t

Q: IF load : 100N and Effort force : 500N How can we calculate Fulcrum force?? Do anyone have a good…

A: GivenLoad=100NEffort force =500N

Q: 13. In jaw crusher experiment, as d80 increase, the power needed to complete crushing: (1 Point)…

A: Crushing is the process in which the size of the material is reduced. The crushing process is widely…

Q: A bronze bearing supports the steel shaft shown in the figure. The shaft has a Brinell hardness (HB)…

A: Brinell hardness (HB) of 150 diameter of 30 mm  length of 30 mm rotates at 200 rpm 4 years (three…

Q: Explain the difference between M-series and T-series high-speed steels.

A: Difference between the M-series high speed steels and T-Series high speed steels M-series- 1. The…

Q: Bar stock of initial diameter = 90 mm is drawn with a draft = 15 mm. The draw e has an entrance…

A:

Q: Design a hollow steel shaft to transmit a torque of 13,000 lb-in. The allowable shear stress in the…

A: Data given - Torque = 13000 lb-in allowable shear stress  = 9000 psi   Answer- Let di and do be the…

Q: Prove that: in square key, the crushing stress is equal to twice of shearing stress.

A:

Q: 6- Justify the selection of standard rolled steel sections in mechanical designs.

A: The properties required for mechanical design are: Strength- The strength is measured by the…

Q: A double acting cylinder is used to transfer work-pieces in a production machine. Both the extend…

A: Given:Force needed, F=3500 NRod diameter, d=15 mm or 0.015 mPressure, P=6 barFriction force=10 % of…

Q: Q3- B/A round disk of 150 mm diameter is to be blanked from a strip of 3.2 mm half hard cold-rolled…

A:

Q: A) What is the axial force along AB? FAR = units B) What must be the minimum diameter of the pin at…

A: Given:P=200 lbFoS=2.5shear stress at failure for the pin material= 16 ksi

Q: Q3/Fill the blanks with its suitable answer. 1) In a successful wire drawing process, the maximum…

A: Wire drawing is a process used to reduce the cross-section of the wire by pulling the wire through…

Q: Which is not a performance factor of the design of a journal bearing? choose answer below…

A:

Q: A strip with a cross section 120 mm x 6 mm is being rolled with 20% reduction area, using rolls of…

A: Given Strip = 120 mm X 6 mm Deduction = 20% Diameter = 400 mm Coefficient of friction = 0.1 To find…

Q: force in ns. Consi

A: Given:

Q: (i) Determine the Force applied on an aluminum specimen subjected to Brinell hardness test. If the…

A:

Q: axial stress developed in the rod

A: Given data; Circular metallic rod of length, l =250 mmTemperature, T= 2000CYoung's…

Q: xplain the main objective of the Dimensioning of a Cylindrical Press Fit Jo

A: Press fit (also called interference or force fit) joint is defined as a fixed, non-dismountable…

Q: An eye bolt carries a tensile load of 20 kN. Find the size of the bolt (in mm), if the tensile…

A:

Q: An aluminium strip with a cross section of 200 mm × 8 mm is being rolled with 25%  reduction of…

A: Given Data: Aluminium strip cross sectional area A=200 mm×8 mm Diameter d=400 mm  Tensile yield…

Q: (3) A single-threaded jackscrew has square threads. The screw diameter is 1 in. and there are 4…

A:

Q: (i)Determine the Force applied on an aluminum specimen subjected to Brinell hardness test. If the…

A: Brinell Hardness test is used to determine the Hardness of any material. In this method, indenter of…

Q: Estimate the force required for punching a 25mm diameter hole through a 3.2mm thick annealed…

A: Given data  Diameter of hole = 25mm  Thickness = 3.2 mm  UTS = ULTIMATE TENSILE STRENGTH = 1000Mpa…

Q: Example 2. energy per hole during each revolution. Each piercing takes 40 per cent of the time…

A: Flywheels are used to store the energy when the supply of the energy is more than the requirements…

Q: A strip with cross section 120 X 6 mm is being rolled with 20 % reduction area, using rolls of…

A: Consider a strip of thickness h0 is undergone rolling operation whose Roll Diameter is D and angle…

Q: Since both the force that cause Bearing Stress to Normal Stress is perpendicular to the cross…

A: Stress : When a material is subjected to an external influence (Force, moment, Torque etc) a…

Q: Determine the direction of slip line at the workpiece tool interface in the condition of coulomb…

A: given; ⇒coefficient of friction (μ)=0.2⇒normal stress (σ)=100N/mm2⇒shear yield strength…

Q: (3) A machine part of uniform thickness t = b/2.5 is shaped as shown and machined all over from AISI…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: Compare the force required to draw (25mm×6mm) capper strip to 45% reduction of area with that…

A:

Q: 2) A 2 mm thick metal sheet is to be bent at an angle of one radian with a bend radius of 100 mm. If…

A: As per given question  R = Bend inside Radius=100mmK = 0.5 because R > 2tt = sheet thickness=2 We…

Q: stress component oy is

A: From the given fig;Strain in the Z -direction is 0Yield strength in uniaxial tension of material of…

Q: A hydraulic punch press is capable of delivering 2,000kPa pressure on its platen from its 250mm…

A: Given: A hydraulic punch press is capable of delivering 2,000kPa pressure on its platen from its…

Q: A mechanical press is powered by a 23-kW motor and operates at 40 strokes per minute. It uses a…

A:

Q: In a stamping operation, a 2 mm thick stainless steel sheet with an ultimate tensile strenght of 900…

A:

Q: Determine the design stress for a rod where the load is reversed bending load. The surface finish…

A: Given, Ksur = 0.8 FOS = 1.3 For Reversed Loading, Ka = 0.8 If σe is the endurance limit for reversed…

Q: Explain the main objective of the Dimensioning of a Cylindrical Press Fit Joint. Emphasize on the…

A: Main objective of a cylindrical press fit joint              Note :- you have posted two different…

Q: 1. What is the working strength of a 2'' bolt which is screwed up tightly in a packed joint when the…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: (b)Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw…

A:

Q: A rectangular workpiece has the following original dimensions: 2a = 120 mm, h = 40 mm and width = 25…

A:

Q: A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of…

A:

Q: A hole with a diameter of 18 mm will be drilled in a sheet material with a thickness of 4 mm.…

A: D = 18 mm t = 4 mm Stress = 640 MPa Shear force (F) = ?

Q: written plz a billet before and after hot forging from an initial size of 2.5 mm x 2.5 mm x 25 mm to…

A: Given      Stress = 18 MPa Length, L = 25 mm Find  Force, F  Work, w

Q: cross-sectional bar, has a diameter of d= 40 mm cut from an AISI 1030 Hot Rolled steel. The bar is…

A:

Q: Ex: Wire is drawn through a draw die with entrance angle 15°. Starting diameter is 2.5 mm and final…

A:

Q: mention the advantages and disadvantages of rolling contact bearing

A: Rolling contact bearings: In rolling contact bearings, the contact between the bearing surfaces is…

Q: Give practical or real world problems/situations on simple, bearing and shear stress

A: A practical example of a body under simple stress is a tyre inflated with air.

Q: Assume you are bending a 3/16” thick rolled plate of Al 6061-T6 at a 90-degree angle. The initial…

A: Solution: Given Data: t=316"Ri=0.35"   Note: Yield strength of Al 6061-T6 is: Sy=35000 psi Young's…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.