Give one advantage and disadvantage of the radial type distribution system.

Q: - What is the amount of power saving in the AM-DSB-SC, when compared to other types of AM systems?

A:

Q: Define and draw unit circle. What is the significance of unit circle for system analysis?

A: to draw and define unit circle significance of unit circle for system analysis

Q: Generation engineers are more inclined to an operation in a closed system as compared to an open…

A: Nowadays Electricity is a major part of any country's growth. The demand for power supply is…

Q: Draw the Schematic diagram of an AC distribution system.

A: AC Distribution system - An AC distribution system is a system in which electrical energy in the…

Q: 2- What is the amount of power saving in the AM-DSB-SC, when compared to other types of AM systems?

A:

Q: Calculate the values of the parameters ?1 and ?2 in order for the closed-loop system, whose block…

A:

Q: What is load capacity? What is the load capacity of a typical residential area, a city? What…

A: LOAD CAPACITY Basically it is the maximum demand,stress or load that can be placed on a given system…

Q: Define the term "local wide network."

A: The given terms are as follows -  1. Local Network 2. Wide Network

Q: Tecom 3. Explain the reality of loss-making beginning and uncertainties in taking ECE ideas to…

A:

Q: WR* = 1 for an I/O read bus operation.  True  False

A: WR is a control signal which is used for input or memory read and write operation.  WR=0 is used for…

Q: Define percentage line and load regulation

A: Line regulation-Line regulation refers to a power supply's capacity to maintain a constant output…

Q: Preference setting is used for controlling what parameter of a generating system and who will take…

A: The real world demands the analysis and design of complex systems. It is possible with the clear…

Q: 1) The Bus Interface Unit (BIU) construction?

A: according to guidelines, we need to solve only first question.

Q: Give four reasons why electroanalytical methods with their advantage over other methods.

A:

Q: What are the advantages and disadvantages of double fed distributor

A: Advantages of double fed distributor are given below, It increases supply reliability. The size or…

Q: What are the advantages of root locus method?

A: The Root locus is define as locus of closed loop pole when system gain K is vary from zero to…

Q: The X/R circuit ratio of an automatic reclosure is inversely proportional to the asymmetrical factor…

A: Automatic recloser: It a type of switchgear that is used in overhead electrical distribution system.…

Q: (a) Name different parts of a distribution system? Give the function of each part.

A: Since both the questions are different so we are supposed to answer 1st one.

Q: Just draw a directional relay circuit design (the design should be only hand written)

A: Protection devices are used in a circuit to protect the equipment and provide safety for humans from…

Q: Discuss the importance of safety in an engineering maintenance from Kasapreku’s case scenario?

A: Answer:  The food and beverages industries has a moral and regulatory obligation to keep the work…

Q: 1. What is the ideal line percent regulation rating? 2. Shunt voltage regulators require  __________…

A: The objective is to determine line regulation and voltage sampling.

Q: Explain why Distortionless transmission is difficult to implement realistically, and explain what a…

A: For distortion less transmission line, time constant of series components  i.e. R/L will be same as…

Q: What is a Direct Radiator Loudspeaker?

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: What is the purpose of sequence control

A: Sequence control is generally used to start or stop motors in a specific order. It is used when one…

Q: estigate the stability of the system using Routh Criterion method.

A:

Q: 2. Explain over modulation.

A:

Q: c) Elaborate the statement that a synchronous machine is 'floating' on the bus bars

A: In an infinite bus the alternators are connected in parallel.

Q: Find the effect of ‘clearing time’ on transient stability. Using the equal area criterion method…

A:

Q: Explain Basic Trip Circuit in Transmission line? Also, Discuss the Fundamental Requirements of…

A: Protection refers necessary isolationof healthy system from faultysystem, so that fault can not…

Q: With necessary sketch, Explain the mode of operation of chopper which is turn off due to external…

A: The mode of operation of chopper circuit is turn off due to the external load circuit so it called…

Q: Write different aspect detail of  Digital carrier systems.

A: A carrier systems is a mechanisms that provides a means to send signals from more than one source…

Q: Which of the following is the busbar type where active power and busbar voltage are input data in…

A: type of bus quantities specified quantities unspecified Generator bus P, V Q, δ Load bus P, Q V,…

Q: Rollover Cable using EIA/TIA-568A and EIA/TIA-568A PIN PIN WIRE LABEL WIRE COLORS WIRE LABEL NO. NO.…

A: Given: To find: The wire label and color?

Q: Choose the correct Answer: The difference in the propagation delay between the fastest and slowest…

A: delay skew is the difference between the propagation delay on the fastest and slowest pairs in a…

Q: For the radial system shown, the setting of the second zone (in secondary settings) of a relay at V…

A: Given CT 1000: 1 VT ratio -132000 : 120               -1100 :1 Second zone

Q: b) What is the difference between systematic and random errors; then list the reasons for equipment…

A: Random Error :-  The uncertain disturbance occur in the experiment is known as random error. These…

Q: Draw a single line diagram showing a typical distribution system.

A: In a power system, there are generation, transmission and distribution with utilization of…

Q: What precautions are practiced by electric companies in terms of loading capacity? When is a…

A: The precautions are practiced by electric companies are given as: Avoid water while operating with…

Q: of a bus bu

A: Given: The answer is shown as:

Q: Derive emf equation of the synchronous generator.

A:

Q: How to verify the validity of the nodal analysis technique in solving electrical networks?

A: Given:   Brief description: In the above question they want to discuss the nodal analysis technique…

Q: A.How are continuous and non-continuous loads for feeder ratings calculated? a. Are demand factors…

A: A. How are continuous and non-continuous loads for feeder ratings calculated? Answer: The feeder…

Q: (ii) Outline the considerations involved in planning a main distribution board

A: (ii) CONSIDERATIONS INVOLVED IN PLANNING THE MAIN DISTRIBUTION BOARD: Present-day structures are…

Q: can you discuss how and why distribution feeders are operated radially?

A: Radial distribution system is used in electrical power systems to provide electrical power supply to…

Q: 1111

A: The image provided by you is not clear , so as much I can understand from figure is that is a…

Q: b) Write any 4 advantages of coaxial cable over shielded twisted pair?

A: Coaxial cables are will work efficiently in small distance     Coaxial cables are used in the…

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.