) Give the resistance and tolerance for a resistor coded with red, violet, red and gold. A. 3800Ω+ 5% B. 3,8000Ω+ 10% C. 2,700Ω+ 5% D. 2,700Ω+ 10% 2) Identidy the corresponding color code of a resistor whose resistance value is 75MΩ+10 A. Violet, green, blue, gold B. gray, blue, violet, gold C. violet, green, blue, silver D. gray, Blue, violet, silver

) Give the resistance and tolerance for a resistor coded with red, violet, red and gold. A. 3800Ω+ 5% B. 3,8000Ω+ 10% C. 2,700Ω+ 5% D. 2,700Ω+ 10% 2) Identidy the corresponding color code of a resistor whose resistance value is 75MΩ+10 A. Violet, green, blue, gold B. gray, blue, violet, gold C. violet, green, blue, silver D. gray, Blue, violet, silver

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter1: General Information For Electrical Installations

Section: Chapter Questions

Problem 15R: You will learn in Chapter 3 that residential lighting loads are based on 3 volt-amperes per ft2 (33...

See similar textbooks

Similar questions

II. OBJECTIVES• Familiarize themselves with resistor color code.• Identify resistors’ value from a color code chart.III. EQUIPMENT1. Multimeter. IV. PROCEDURE1. Write down the resistor band colors for each of the resistors.(image uploaded) 2. Using the color codes determine the components theoretical resistance. 3. What are the color bands on the following value resistors all of which have a 5% tolerance?i. 22 k Ω ___________________________________________________________ ii. 10 Ω ___________________________________________________________iii. 10 k Ω ___________________________________________________________iv. 470 kΩ __________________________________________________________v. 33 kΩ ___________________________________________________________ V. CONCLUSION
You will learn in Chapter 3 that residential lighting loads are based on 3 volt-amperes per ft2 (33 volt-amperes per m2). Determine the minimum lighting load required for an area of 186 m2. Do calculations for both feet squared and meters squared so you can see the difference in answers. To convert meters squared to feet squared, refer to Table 1-8.
Q1. A circuit with R1= 1 Kilo ohm is connected in series with R2=3 Kilo ohm, if RL is attached in parallel with R2, then the voltage across R1 doubles. What is the value of RL if you know that the total applied voltage is 40 volt? * *
Give the value of the following resistors: (GIVE SOLUTIONS)(Must write final value to short notation using KOhms, MOhms, etc. if applicable)1. Red, red ,orange, silver2. Blue, red, orange, gold3. Brown, Black, Orange, gold4. Red, Green, blue, gold5. Violet, green, red, silver
Find the Voltages of all four nodes in the diagram for the following questions.(USE NODAL ANALYSIS) Please show all work!! (a) b0 is a voltage source of 1 Volt, b1,b2,and b3 are not voltage sources, b0 is the only independent source in the system (b) b1 is a voltage source of 2 Volts, b0,b2,and b3 are not voltage sources, b1 is the only independent source in the system (c) b2 is a voltage source of 4 Volts, b1,b0,and b3 are not voltage sources, b2 is the only independent source in the system (d) b3 is a voltage source of 8 Volts,b1,b2,and b0 are not voltage sources, b3 is the only independent source in the system
Three resistors R1,R2, and R3, are connected in series and to a 120-volt source. If R2 = 2R1, R3 = 3R1, and the total power taken by the circuit is 200 watts, calculate (a) the resistance of each resistor, ( b) the power in each resistor
Calculate and measure the current of each mesh, i1,i2,io- Calculate and measure the power in each of the resistors- Calculate and measure the voltage across the resistors 20,12,8
What is the resistance of the Aluminum bus bar on the outdoor substation which has a diameter of 4 inches and 15 ft long if the resistivity of each bar is 2.82x10-8 Ohm-m? a. 1.6555 x 10^-5 Ohm b. 1.5907 x 10^-5 Ohm c. 1.6555 x 10^-6 Ohm d. 1.5907 x 10^-6 Ohm
Determine the voltage across resistor 2, VR2with E=8V, R1=581 ohms and R2=750 ohms.
Refer to the Graphics Appendix. If all the resistors are 0.5 Watt, will any of the resistors be overloaded? R2 R2 and R4 R1 and R3 No resistors are overloaded.
What is the value of the current and voltage drop across 6Ω resistor respectively for the circuit shown below? 3A, 36V 3mA, 18V 3A, 6V 3A, 18V
2 - Which of the following is correct for ammeter?I. It is connected in series to the circuit.II. If it is connected in parallel to the circuit, it will short-circuit the branch it is connected to.III. Its internal resistance is very large. A) I, II and III B) Only I C) I and II D) II and III E) I and III