Given a partial wood wall stud that is to be covered with marine plywood and lumber to be used for its wall stud is 2” x 2” x 10’ with a total length of 5.50 and a wall thickness of 0.075m.a. How many pieces of 2” x 2” x 10’ lumber is required? (use interior area only)b. If per board foot is ₱40.00, what is the total cost for its construction?c. How many kilograms of 2½” Ro. CWN is needed?d. How many pieces of Marine Plywood is needed? NAME:COURSE & YEAR:SUBJECT:DATE:Given a partial wood wall stud that is to be covered with marine plywood and lumberto be used for its wall stud is 2" x 2" x 10' with a total length of 5.50 and a wallthickness of 0.075m.a. How many pieces of 2" x 2" x 10' lumber is required? (use interior area only)b. If per board foot is P40.00, what is the total cost for its construction?c. How many kilograms of 22" Ro. CWN is needed?d. How many pieces of Marine Plywood is needed?5.00m6.50m2.80m

Answered: Image /qna-images/answer/bec86f12-840c-4a5b-9fdc-0c3bfe366c4c.jpg

Given a partial wood wall stud that is to be covered with marine plywood and lumber to be used for its wall stud is 2” x 2” x 10’ with a total length of 5.50 and a wall thickness of 0.075m. a. How many pieces of 2” x 2” x 10’ lumber is required? (use interior area only) b. If per board foot is ₱40.00, what is the total cost for its construction? c. How many kilograms of 2½” Ro. CWN is needed?

Given a partial wood wall stud that is to be covered with marine plywood and lumber to be used for its wall stud is 2” x 2” x 10’ with a total length of 5.50 and a wall thickness of 0.075m. a. How many pieces of 2” x 2” x 10’ lumber is required? (use interior area only) b. If per board foot is ₱40.00, what is the total cost for its construction? c. How many kilograms of 2½” Ro. CWN is needed?

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter37: Section Layout

Section: Chapter Questions

Problem 37.3Q

See similar textbooks

Similar questions

Assuming all dimensional lumber framing, list all elements that will see shrinkage in the vertical direction. What is the required size and spacing of nails if used to fasten the floor sheathing to the joists – assume 7/8” osb is used for the subfloor. What is the nailing requirements between the 2 top plates of the wall? Provide a sketch of this deta
Dimension of the exterior ceiling is 4 - 1.00m x 15.00m. How many pieces of plywood is necessary to cover the ceiling? a. 21 pcs. Ordinary Plywood b. 20 pcs. Ordinary Plywood c. 20 pcs. Marine Plywood d. 21 pcs. Marine Plywood
You must have to draw FBD
What lumber grade has > 80% clear wood?
Dimension of the interior ceiling is 7.00m x 9.00m. How many pieces of plywood is necessary to cover the ceiling? a. 21 pcs. Ordinary Plywood b. 22 pcs. Marine Plywood c. 22 pcs. Ordinary Plywood d. 21 pcs. Marine Plywood
What is Parallel and Oriented Strand Lumber?
b) centroid location of the transformed section in the vertical direction. Enter your answer in mm to 1 decimal place. Hint: transform CFRP into an equivalent amount of wood. Calculate the position of the centroid relative to the bottom edge of the transformed section, i.e. centroid position is measured upward from bottom edge of section.
I WILL UPVOTE IF ORIGINAL WORK ASAP
Research 7. structural spot details (wood, reinforcing Concrete)
a. plumb bob b. spirit level c. pegs d. butt rod
Please give me right solution. A wall partition 5.8m long and 3.4m high specify the use of 2”x3” studs space at 60cm on both ways. Find the total board ft required ?
Define spudding