need only 4 and 5 quicky. Given an Emitter-Stabilized Bias Common Emitter amplifier with the following data:VCC = 12 V, Ic = 2 mA, Vc = 7.6 V, VE = 2.4 V and B = 801. The emitter current is equal to:A. 2.025 mA B. 1.975 mAC. 197.5 µAD. 25 μA2. The collector to emitter voltage is equal to:A. 12 VB. 7.6 VC. 5.2 VD. 4.4 V3. The emitter resistor is:A. 1,185.19 Q B. 1,215.19 QC. 12,151.90 ΩD. 96 KQ4. The collector resistor is:Α. 4,800 ΩΒ. 15,500 ΩC. 3,400 ΩD. 2,200 Ω5. The base resistor is:Α. 381,200 Ω Β. 356 ΚΩC. 148 KQD. 60 Q

Given an Emitter - stabilized bias common emitter amplifier 4) to find the value of collector…

Given an Emitter-Stabilized Bias Common Emitter amplifier with the following data: Vcc = 12 V, Ic = 2 mA, VC = 7.6V, VE = 2.4 V and B = 80 1. The emitter current is equal to: A. 2.025 mA B. 1.975 mA C. 197.5 μA D. 25 μA 2. The collector to emitter voltage is equal to: A. 12 V B. 7.6 V C. 5.2 V D. 4.4 V 3. The emitter resistor is: A. 1,185.19 Ω Β. 1,215.19 Ω C. 12,151.90 Ω D. 96 ΚΩ 4. The collector resistor is: Α. 4,800 Ω Β. 15,500 Ω C. 3,400 Ω D. 2,200 Ω 5. The base resistor is: Α. 381,200 Ω Β. 356 ΚΩ C. 148 ΚΩ D. 60 Q

Given an Emitter-Stabilized Bias Common Emitter amplifier with the following data: Vcc = 12 V, Ic = 2 mA, VC = 7.6V, VE = 2.4 V and B = 80 1. The emitter current is equal to: A. 2.025 mA B. 1.975 mA C. 197.5 μA D. 25 μA 2. The collector to emitter voltage is equal to: A. 12 V B. 7.6 V C. 5.2 V D. 4.4 V 3. The emitter resistor is: A. 1,185.19 Ω Β. 1,215.19 Ω C. 12,151.90 Ω D. 96 ΚΩ 4. The collector resistor is: Α. 4,800 Ω Β. 15,500 Ω C. 3,400 Ω D. 2,200 Ω 5. The base resistor is: Α. 381,200 Ω Β. 356 ΚΩ C. 148 ΚΩ D. 60 Q

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

for a common emitter amplifier shown (beta=100) (R1=15k, R2 = 8.2k) Compute for Zin, Zout, Bre, Rth, Vc, Vb, Ib, Voltage Gain, and Current Gain
4) By drawing the small signal model of the circuit given below, we can determine the total voltage and current gain values of the circuit, without the bypass capacitor on and without the bypass capacitor. Calculate separately for the two cases as it will be in the circuit (connected to the emitter end of the transistor). (β = 100, rS = 600 Ω, R1 = 27 KΩ, R2 = 4.7 KΩ, RC = 3.3 KΩ, RE = 680 Ω, RL= 15 KΩ, VCC = 10 V)
A transistor in a circuit showed has the following Maximum rating Pdmax=800mAw, Vcemax=15v, Icmax=100mA. Determine the maximum value to which Vce can be adjusted with out exceeding any rating which rating will be exceeded first
In the circuit given in the picture, the emitter follower is connected to a non-ideal voltage source Vs with a source resistance Rs.These are the value: beta =100Vbe = 0.7VVce,sat = 0V.The sub questions for this problem are:a. If Rs = 0 and Vs = 3V, determine the value of Vo.b. If Rs = 5k Ohms and Vs = 3V, determine the value of Vo.c. If Rs = 5k Ohms , determine the value of Vs that will cause the BJT to start saturating.
The transistor is specified to have Bf in the range of 7 to 35. The load resistance is Rc = 9 ohms. The dc supply voltage is Vcc = 180V and the input voltage to the base circuit is VB = 8V. If VCE (Sat) = 1,1 V and VBE (sat) = 1,6, determine: The value of RB that results in an ODF of 4 A. 0,7514 ohm B 0,5634 ohm C. 0,5081ohm D. 1 ohm The Power loss in the Transistor A. 35,07 W B. 44,30 W c. 40,04 W D. 23,65 W
5. Choose the correct answer: a) The reason of high input resistance of the MOSFET is: 1. The insulator layer. 2. The reverse biasing. 3. The forward biasing. b) Which transistor has no Ipss parameter?. 1. JFET. 2. E-MOSFET. 3. D-MOSFET. ¢) For an n-channel D-MOSFET transistor, at what condition can gm be greater than gmo?. 1. Vs is positive. 2. Vgs is negative. 3. Vas =0. d) A certain amplifier has an Rp=1KQ. When a load resistance of 1KQ is capacitively coupled to the drain, the gain will reduce to the: 1. Half. 2. Quarter. 3. Not change.
The dc bias circuit for a common emitter amplifier is shown in the figure. In the circuit, Vcc=15v,RB1=20k Ω,RB2=100k Ω,Rc=5.1k Ω,and RE1=1k Ω, Assume that when the transistor is on, the voltage drop from base to emitter VBE=0.7v. Also assume that β= ∞, which implies that the base current can be considered zero (IB=0) in your calculations. Solve for the base voltage VB. Solve for the emitter voltage VE. Solve for the emitter current IB. Solve for the collector current IC
Find the short-circuit time constants and fL for the common-source amplifier As Shown if ID = 1.5 mA and VGS−VTN = 0.5 V. Assume λ = 0.015/V. The other values remain unchanged.
An npn transistor with IS = 1 × 10−16 μA, αF =0.975, and αR = 0.5 is operating with VB E = 0.70 Vand VBC = 0.50 V. By definition, this transistor isoperating in the saturation region. However, in thediscussion it was noted that this transistor actually behaves as if it is still in the forwardactive region even though VBC > 0. Why? Use thetransport model equations to justify your answer
Find the rout resistance, the ro internal resistance of the mos transistor will not be neglected, transistör Gm vapura are not the same
Considering the given transistor circuit and given values(β=60; V BE =0,5 V; VCC =15V; R E=1K ; R c=10K ; R1=60K ;R2=30K ).a. Find the base, collector, and emitter currents b. Find the voltage gain of this circuit c. Find the voltage gain by ignoring the capacitor connected to the emitterd. Briefly describe the transistor active zone and state its importance
Given: Voltage Divider Bias Circuit Supply: 10Vdc to 24Vdc Load: 1000 ohms Voltage Gain: 80 to 400 Lower Cutt off Frequency: 100Hz Sinusoidal source (zero internal resistance): 50mVp-p Transistor: Si, beta=75 Base-Collector Capacitance= 8pF Base-Emitter Capacitance= 25pF Design a Single-stage Common Emitter Class A Amplifier and compute the following: a) dc load line b) hie c) midband gain d) Miller equivalent Capacitances e) upper cut off frequency