Given: H = 7 m H2 = 4.3 m Calculate the seepage loss per meter length of the sheet pile (at right angles to the cross section shown). Bear in mind that in the flow net of the system the number of flow channels is Nf = 1 and the number of potential drops is Ng = 3. - Sheet pile H D, k = 4 × 10-4 cm/sec Impermeable layer

Given: H = 7 m H2 = 4.3 m Calculate the seepage loss per meter length of the sheet pile (at right angles to the cross section shown). Bear in mind that in the flow net of the system the number of flow channels is Nf = 1 and the number of potential drops is Ng = 3. - Sheet pile H D, k = 4 × 10-4 cm/sec Impermeable layer

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter8: Seepage

Section: Chapter Questions

Problem 8.3P

See similar textbooks

Similar questions

The value of k of soil around a sheet pile is 10-6 m/s. The flow net of this sheet pile consists of 5 flow lines and 11 equipotential lines. Determine the rate of seepage (in cm3/s per m) if the difference in the water level is of 4m.
Determine the factor of safety against heave on the downstream side of the single-row sheet pile structure shown in Figure 9.30. Use the following soil and design parameters: H1 = 7 m, H2 = 3 m, thickness of permeable layer (T) = 12 m, design depth of penetration of sheet pile (D) = 4.5 m, and γsat = 17 kN/m3
For the flow net shown in the figure below, if the datum is selected at the downstream water surface, determine: (a) the total head at point b; (b) the pressure head at point b if point b is 11 m below the downstream ground surface (or 13 m below the downstream water surface); (c) uplift pressure at point b; (d) the factor of safety against heave on the downstream side of the single-row sheet pile structure shown below. The depth of penetration of sheet pile (D) is 4.5 m. (Note: the blue dashed area is the heave zone)
The Figure below shows a long pile wall driven in sand with Coefficient of permeability K= 0.05cm/sec.it is required to: 1.Estimate the max. possible value of dimension h, where Ah=1.2. 2.Calculate the seepage loss (m /day) per meter of wall
Draw a flow net for a single row of sheet piles driven into a permeable layer as showin Figure Q3 (b) below. Thus, determine the seepage loss per meter length of thesheet pile.H1 = 9.6 m D = 5 mH2 = 3.7 m D1 = 13 m
The sheet pile is driven in the Cebu South reclamation area and the area to one side is pumped down as shown in the flow net. The permeability of the sand is 0.001 m/s. below the elevation of 20 m us an impermeable rock layer. Determine the flow per unit length.How high (above the ground surface) the water will rise if a piezometer will be placed at A?
Refer to Figure 8.23. Given:• H1 = 6m• H2 = 1.5 m• D = 3 m• D1 = 6 mDraw a flow net. Calculate the seepage loss per meter length of the sheet pile (at a right angle to the cross section shown).
Given the sketch of half of a symmetrical Flow Net shown in Figure H8-4, compute the total head, pressure head, and elevation head for a point halfway up the sheet pile from its base, on either side of the sheet pile (i.e., Points C and B are on the left and right faces of the sheet pile). Assume the water is 5 m and 1 m above the ground surface in the upstream and downstream sides of the sheet pile, respectively. Use the bottom of the silty sand soil as the Datum.
A flow net for flow around a single row of sheet piles in a permeable soil layer is shown in Figure below with a scale as shown. Given that kx = kz=k = 4 x 10-3 cm/sec, determine How high (above the ground surface) the water will rise if piezometers are placed at points a and b The total rate of seepage through the permeable layer per unit length The approximate average hydraulic gradient at c factor of safety against piping x=1.6 y=2.8
a) Determine the seepage loss per meter length of the sheet pile if hydraulic conductivity, k is 4.1 X 10-4 cm/sec.
(c) A dam shown in Figure Q1 (c) retains 6m of water. A sheet pile wall on the upstreamside (which is to reduce seepage under the dam) penetrates 4m into a 10m thick of siltysand stratum. Below the silty sand is a thick deposit of clay. Assume that the silty sandis homogeneous and isotropic. (i) Calculate q in cm/s.(ii) Analyze the pore water pressure distribution on the front of the sheet pile (atevery 2m @ at points A, F and G). Given the Nd of points A, F and G are 0.5,1.5 and 3.0 respectively.(iii) Analyze the pore water pressure distribution at the base of the dam. (at every5m @ at points A, B, C, D and E). Given the Nd of points A, B, C, D and E are5.6, 6.7, 8.0, 10.0, 13.0 respectively.(iv) Determine the uplift force under the dam.(v) Calculate the factor of safety against piping. Given Lmin = 0.85m.
The sheet pile shown on the figure below is driven into a soil with a permeabilityk = 22 × 10-4 cm/s. Calculatea- the seepage loss per metre lengthb- the pore water pressure at the 12 points shown on the figure.