Given: K;= K2= 300 K3= Kş= 200 K= 500 K= 600 F1= 100 F2= 200 Where, K.( i=1 to 6) are the spring constants and F, and F2 are loads K1 K3 >F1 K2 K4 3 K5 K6 >F2 a) Apply Minimum Potential Energy method to develop system of equations. Write in the form of [K]{u} = {f} where [K] is the stiffness matrix, {u} unknowns, {f} force vector. b) Find net deformation in springs, {u} vector c) Find force in each spring. 2)

Given: K;= K2= 300 K3= Kş= 200 K= 500 K= 600 F1= 100 F2= 200 Where, K.( i=1 to 6) are the spring constants and F, and F2 are loads K1 K3 >F1 K2 K4 3 K5 K6 >F2 a) Apply Minimum Potential Energy method to develop system of equations. Write in the form of [K]{u} = {f} where [K] is the stiffness matrix, {u} unknowns, {f} force vector. b) Find net deformation in springs, {u} vector c) Find force in each spring. 2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Chapter 7, Problem 63, there is an 'h' value that is solved when expressing half the width of the Rankine Oval that I am not quite understanding the process by which the value is solved for. Could you break down the process by which h=0.02423 m? It's been a while since I was last in school, so the mathematical method by which 'h' was solved is a little unclear to me.
a) Let R represent the reaction force at Support B. By releasing the beam at Support B and imposing a force R at Point B, the deflection of the beam consists of two parts,i.e. Part I- the deflection caused by MB ; Part II- the deflection caused by R Please treat R, w, h , L , E as variables in this step , the mathematical equation for the deflection at Point B caused by R ( Part II) can be written as (Hint : to input equation R2LQ2wh , you can type (R^2*L)/(Q^2*w*h) ) b) Using the provided data: cross-section width w = 20 mm, cross-section hight h = 93 mm, length of the beam L =3 m , beam material’s Young’s modulus Q =226 GPa, applied bending moment MB = 11 kN.m The value of the deflection at Point B caused by MB ( Part I) can be calculated as ......(in mm)
Points for stress vs strain (in image) Assume the compressive concrete strength (f’c) is 3,000 lb/in2 (psi)Calculate a cubic function (3rd order polynomial – Ax3+Bx2+Cx+Constant)Use this function to create a function that describes the slope of the cubic function (the derivative of thecubic function). This new function allows you to calculate the tangent to any point along the curve. Thetangent is the modulus of elasticity (E). The concrete code provides a formula to calculate E for concrete. That formula is:E = 57,000√??′, where f’c is in units of psi, and E is in units of psi.Use the derivative function you calculated to locate the point on the curve where the slope of the curvematches E using the concrete code formula. Express that stress point on the curve as a percentage ofthe compressive strength of the concrete. Now, calculate the secant modulus for the test case using 1,500 psi (50% f’c) as the arbitrary point onthe curve.Assume fracture occurs at the last point…
Parameters Mass 5kg A=2 B=7 C(m)=3 D(m)=4.583
Vibrations Question The following mass–spring system is sliding on a surface of kinetic friction.The system has the following parameters for initial design purposes subject to changes based on overall system performancem=100 kg, k=1300 N/m , x(0)=0.4 , v(0)-0.01, uk=0.08, F(t)=01. Obtain the equation of motion of the system2. Derive the equivalent first-order ODEs with initial conditions to represent part 1
Laplace transformation
Please show how to derive cagliotti function.
Use the 3 relations (equations) below to relate T(°F) to T(°C). Then, find out, at what temperature a Fahrenheit and a Celciusthermometer would read the same numerical value.
Electric drives have a wide range of applications in various industries. One common application is in the manufacturing industry, where electric drives are used to control the speed and torque of electric motors that drive various machines and equipment. For example, electric drives are used in conveyor systems, pumps, fans, compressors, and machine tools to regulate the motion and force required for different manufacturing processes. 1. Create simple Process Flow Diagram (PFD) of electric motor used in pumps.
Find the equivalent spring constant spring constant of the system.
Given: Mass = M, Radius = R, Moment of Inertia = I, Distance = H, Gravity = g, Initial timing = 0 Unknown = How long will the [delta t] process take? (time) Please keep in mind that almost every variable is unknown! We are given no numbers and are instructed to generate a solution using the variables [ "R, M, g, I and H." ] Target = Find an equation that, if we could substitute numbers, would determine how long the process would take. Newton's second law and torque seem to be relevant based on how the problem is written. * Also please show drawing based on what we are calculating
The temperature of an experimental heated enclosure is being ramped up from 80 to 450°F at the rate of 19°F/min. A thermocouple, embedded in a Thermowell for protection, is being used to monitor the oven temperature. The thermocouple has a time constant of 84 s. At t = 10 min, what is the difference between the actual temperature and the temperature indicated by the thermocouple? Final answer in whole number. Please show your complete solution and write readable.