Given that P1 = 3N is applied to joint D, P2 = 12N is applied to joint C, P3 = 3N is applied to joint E, and P4 = 12N is applied to joint B. If a = 5m, determine the force in members BF, BG, and AB. Indicate if the members are in tension or compression. Assume tension to be positive. Note: Joint A is connected to a pin and joint G is connected to a roller. a P₁ D P2 C P3 E a PA B F a FBF: FBG: FAB N N N A a G

Given that P1 = 3N is applied to joint D, P2 = 12N is applied to joint C, P3 = 3N is applied to joint E, and P4 = 12N is applied to joint B. If a = 5m, determine the force in members BF, BG, and AB. Indicate if the members are in tension or compression. Assume tension to be positive. Note: Joint A is connected to a pin and joint G is connected to a roller. a P₁ D P2 C P3 E a PA B F a FBF: FBG: FAB N N N A a G

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Referring to the figure, determine the forces in members FH, GH and DG using method of joints
Given the figure below determine the bar force at AB and BD
Determine the force in each bar of the truss shown in the figure in terms of P.
Refer to the figure, Beam Properties: Rod Properties: I = 198 x 10^6 mm4 Diameter = 11 mm E = 200 GPa E = 200 GPa Determine the following: a) Due to triangular load α, the rod support at right elongates by 5 mm. Find the force (kN) in rod which caused the elongation. b) Determine the value of α in kN/m? c) Determine the moment at fixed end in kN
Determine The Moments Acting At The Ends Of Each Member. Assume The Supports At A And D Are Fixed. The Moment Of each member is indicated in the figure. E = 29 X 10^3 Ksi.
A tripod shown supports a load of P = 1000 N at point A. Take note that ball and socket joints are used to mount the triopd at points B, D, and C. Consider the following:L1 = 2L2 = 4L3 = 5θ = 45°α = 30 Point C coordinates: (2, -2, 3) *Do not use Vectors in solving Determine the following: Force of AB = __NForce of AC = __NForce of AD = __N
Solve for forces: AB, CH, CD and DF. (indicate units and determine if it is tension or compression)
q(x)= q0[1-c(x/L)] is the distributed load in the truss system given in the figure. It is a built-in support on both supports. a) Calculate the elastic curve equation from the distributed load. b) Find the support reactions. (q0= 6, c=1, L=1) (fixed on both sides)
Problem 3: If the length of all the members is equal on the figure as shown below, determine the force of member AC and BC and state whether it is compression or tension.
The bar ABCD has a built-in support at A. Calculate the force and the couple exerted by the support on the bar. Neglect the weight of the bar and express the answers in vector form. Show the FBD
Solve for the Forces in members CF and EH using the method of joints. Indicate if it is a tension or a compression member
The frame shown supports a load W DE 1000 lb through the cable that passes through 3 pulleys and at the end is attached to a frame, also supports the distributed loads ω1 = 100 lb / ft; ω2 = 60 lb / ft and ω3 = 50 lb / ft. Determine: 1. Reactions at supports A and E. 2. Forces acting on bar ABCDE, show the results in graphical form of the beam. That is, you must make the simplified free-body diagram of the loads that act only on the horizontal element. 3. Make the shear force and bending-moment diagrams for the entire beam. The geometry and load data are as follows: see the geometry and load in the images. Clarification: THE CABLE GOES BEHIND THE FRAME AND THE CONTACT IS ONLY WITH THE PULLEYS AND THE GRIP TO THE FRAME (WALL).All pulleys have the same radius.