Question The electric motor exerts 600 Nm torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys B and C are as shown. 250 Nm 350 Nm 40 mm 45 mm 50 mm 0.9 m 1.1 m a. Knowing that G = 16 GPa and B and C Section of the shaft is hollow with internal diameter of 30 mm. Determine the angle of twist between B and C. Provide the answer in degrees with precision to two decimal points. b. Knowing that G = 12 GPa for C and D part, and C and D Section of the shaft is solid. Determine the angle of twist between C and D. Provide the answer in degrees with precision to two decimal points.

Question The electric motor exerts 600 Nm torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys B and C are as shown. 250 Nm 350 Nm 40 mm 45 mm 50 mm 0.9 m 1.1 m a. Knowing that G = 16 GPa and B and C Section of the shaft is hollow with internal diameter of 30 mm. Determine the angle of twist between B and C. Provide the answer in degrees with precision to two decimal points. b. Knowing that G = 12 GPa for C and D part, and C and D Section of the shaft is solid. Determine the angle of twist between C and D. Provide the answer in degrees with precision to two decimal points.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rod 3.5 feet long rotates in a horizontal plane about a vertical axis through its center. At each end of the rod is fastened a cord 6 ft. long. Each cord is inclined at Ø = 450 with the vertical and supports a weight of 45 lbsA. Which of the following gives the speed of rotation “n” in rpm?a) n = 25.12 rpm b) n = 25.12 rpm c) n = 30.20 rpmd) n = 22.13 rpm B. What is the tension in the 5 feet long cord? a) T = 58.47 lbb) T = 63.63 lbc) T = 51.78 lb d) T = 48.25 lb
A solid shaft made of steel [G = 80 GPa] is subjected to the torques shown. Determine theangle of twist along the shaft measured at gears B, C, D, and E relative to the flange A. Diameter of the shaft is d= 20mm. [TB = 25 N.m; TC = 35 N.m; TD = 24 N.m; TE = 14 N.m][dABCDE = 20 mm (diameter); LAB = 300 mm; LBC = 400 mm; LCD = 400 mm; LDE = 250 mm]
The mass of block B is 95kg while that of A is 59kg. A horizontal force P=468N is applied at block A. The cutting angle is 30.296 degrees. Neglect friction. Computations must observe D`Alembert's Principle. a) Determine the normal force of contact between block A and block B. Express answer in Newtons or KiloNewtons.b) Determine the acceleration of block A. Express answer in meters per seconds.c) Determine the acceleration of block B. Express answer in meters per seconds.
The 14.6 lb lever OA with 9.6 in radius of gyration about O is initially at rest in the vertical position (?= 90°) where the attached spring of stiffness k = 4.3 lb/in is unstretched. Calculate the constant moment M applied to the lever through its shaft at O which will give the lever an angular velocity ? = 5.9 rad/sec as the lever reaches the horizontal position ? = 0.
4. An aerial copper wire (E =1x 10 5 N/mm ^2) 40 m long has cross sectional area of80 mm2 and weighs 0.6 N per meter run. If the wire is suspended vertically, calculatethe maximum weight which this wire can support at its lower end if the limiting valueof stress is 65 N/mm 2.a. 4627 Nb. 4281 NC. 4519 Nd. 5188 N
A cantilever beam 3 m long carries a uniformly varying load zero at fixed to 1200 N/m at free end. Assume that E = 10 GPa and I = 30 x 10x10⁶ mm⁴. 1. Which of the following most nearly gives the deflection at free end? a. 21.4 mm b. 29.7 mm c. 38.1 mm d. 18.5 mm 2. Which of the following gives the deflection at a section 2 m from fixed end? a. 10.5 mm b. 20.3 mm c. 16.4 mm d. 14.8 mm 3. Which of the following gives the rotation at a section 2 m from fixed end? a. 0.421° b. 0.914° c. 0.739° d. 0.614°
The ends of a 0.25kg rod AB are constrained to move along slots cut in a vertical plate as shown. A spring of constant k=3N/m. is attached to end A in such a way that its tension is zero when θ=0°. the rod is released from rest when θ=45° (position 1) until it reaches θ=0° (position 2) Is the work done by the weight of the rod negative and positive for the spring? Please explain.
The 600mm diameter steel shaft is subjected to the torques shown. Determine the angle of twist of end A with respect to C, in . Assume G = 75 GPa. P=74 Ex. 3P= 3(74) = 222 2P= 2(74) =148
The 600mm diameter steel shaft is subjected to the torques shown. Determine torsion at each section. Assume G = 75 GPa. P=74 1.5P= 1.5(74) = 111 kNm 3P= 3(74)= 222kNm
Determine the unstretched length of spring AC if aforce P = 80 lb causes the angle θ = 60° for equilibrium.Cord AB is 2 ft long. Take k = 50 lb/ft.
Please reply as soon as posible, thanks! I don´t have much time:( Static Problem: The spool shown in the figure has a weight of WAB = 27,50 N , and its center of gravity is located at its geometric center ?, the spool has a larger radius ?=0,17 and an inner radius ?=0,13, and it has a coiled rope. Block C has a uniform weight WC= 60 N. Consider the friction between block C and the top of the spool at A, between the spool and the surface at point B and between the rope and pulley D, the friction coefficients are respectively: ?? μs@A=0,30, μs@B =0,45 and μs@D=0,35. The chord is parallel to the plane. Carry out: a) The free-body diagrams of the block and the reel. b) The calculation of the maximum value of P that can be applied without losing the equilibrium of the system.
2/88 If the resultant of the forces shown passes through point A, determine the magnitude of the unknown tension T, which acts on the braked pulley. 275 N 1600 N 0.5 1.5 m- 1.8 m m 300 N A 1.25 m B 50° 0.6 m 650 N